Difficulty
Moderate
Steps
16
Time Required
15 minutes
Sections
3
- Battery
- 2 steps
- Lateral Function Port Panel
- 7 steps
- Cassette Holder
- 7 steps
Flags
0
BackJVC GR-D72U
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
This guide requires removing a lot of screws so it is important to keep track of which screw goes where. All screw heads are Phillips size #000.
What you need
Step 1
Battery
- Locate button on bottom of camera.
- Slide button to the right.
Locate button on bottom of camera.
Slide button to the right.
1024
Step 2
- Pull the battery towards the bottom of the camcorder while lifting battery .
Pull the battery towards the bottom of the camcorder while lifting battery .
Step 3
Lateral Function Port Panel
- Remove silver plate that says “Auto Light” on the top of the camera using a metal spudger.
- Remove the 3.1 mm screw.
- Remove the three 5.3 mm screws from the back of the camera.
Remove silver plate that says “Auto Light” on the top of the camera using a metal spudger.
Remove the 3.1 mm screw.
Remove the three 5.3 mm screws from the back of the camera.
Step 4
- From the bottom of the camera remove the following four screws:
- 5.3 mm
- 3.1 mm
- 5.1 mm
- 3.5 mm
From the bottom of the camera remove the following four screws:
5.3 mm
3.1 mm
5.1 mm
3.5 mm
Step 5
- Use the small plastic opening tool to remove the blue side cover piece.
Use the small plastic opening tool to remove the blue side cover piece.
Step 6
- Remove the 3.1 mm screw on top of the camera, closest to the LCD monitor.
- Remove the 5.4 mm screw next to the snapshot button.
Remove the 3.1 mm screw on top of the camera, closest to the LCD monitor.
Remove the 5.4 mm screw next to the snapshot button.
Step 7
- Remove the 3.1 mm screw next to the USB and DV inputs.
Remove the 3.1 mm screw next to the USB and DV inputs.
Step 8
- Gently pull apart both halves of the camera to reveal the inner components.
Gently pull apart both halves of the camera to reveal the inner components.
Step 9
- Flip the cable locks to the up-position and pull both cables connecting the lateral function port panel to the rest of the camera.
- Insert the cables from the new port panel into their inputs and flip the locks to the down position.
- It is easier to use tweezers when inserting the cable but not required.
Flip the cable locks to the up-position and pull both cables connecting the lateral function port panel to the rest of the camera.
Insert the cables from the new port panel into their inputs and flip the locks to the down position.
It is easier to use tweezers when inserting the cable but not required.
Step 10
Cassette Holder
- From the inside of the camera remove these six screws.
- 3.3 mm
- 3.6 mm
- 3.1 mm
- 4.3 mm
- 4.3 mm
- 3.7 mm
From the inside of the camera remove these six screws.
3.3 mm
3.6 mm
4.3 mm
3.7 mm
Step 11
- Unplug the three cables from the circuit board.
Unplug the three cables from the circuit board.
Step 12
- From the top of the camera remove the two 3.1 mm screws securing the lens to the camera frame.
- From the bottom of the camera remove the 3.2 mm screw next to the battery release switch.
- Remove the 9.1 mm screw next to the menu and volume control label.
From the top of the camera remove the two 3.1 mm screws securing the lens to the camera frame.
From the bottom of the camera remove the 3.2 mm screw next to the battery release switch.
Remove the 9.1 mm screw next to the menu and volume control label.
Step 13
- Remove the lens cap housing.
- Remove the two 3.1 mm screws from the inside of the camera.
Remove the lens cap housing.
Remove the two 3.1 mm screws from the inside of the camera.
Step 14
- Remove the plastic cover piece next to the silver light button.
- Remove the 3.1 mm screw securing the lens to the circuit board.
- Remove the two 3.3 mm screws from underneath the battery port.
Remove the plastic cover piece next to the silver light button.
Remove the 3.1 mm screw securing the lens to the circuit board.
Remove the two 3.3 mm screws from underneath the battery port.
Step 15
- Take the cassette holder and circuit board by lifting it out of the camera frame.
- Remove the two 3.6 mm screws.
- Remove the two 1.8 mm screws then the plate.
- If you are following this guide to replace the LED light or microphone you do not need to follow this step or the next step.
Take the cassette holder and circuit board by lifting it out of the camera frame.
Remove the two 3.6 mm screws.
Remove the two 1.8 mm screws then the plate.
If you are following this guide to replace the LED light or microphone you do not need to follow this step or the next step.
Step 16
- Remove the six cables (one is underneath the metal plate) connecting the cassette holder to the circuit board.
- To unplug two of the cables you must first pull the lock tabs out (towards the cable) then remove the cable.
Remove the six cables (one is underneath the metal plate) connecting the cassette holder to the circuit board.
To unplug two of the cables you must first pull the lock tabs out (towards the cable) then remove the cable.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 2 other contributors
Jonah Powers
Member since: 09/28/2017
422 Reputation
4 Guides authored
Badges:
9
+6 more badges
Team
USF Tampa, Team S2-G2, Nance Fall 2017
Member of USF Tampa, Team S2-G2, Nance Fall 2017
USFT-NANCE-F17S2G2
4 Members
5 Guides authored
