Difficulty

Moderate

Steps

15

Time Required

                          5 - 10 minutes

Sections

4

  • Battery
  • 5 steps
  • Battery Cover
  • 1 step
  • LCD Cover
  • 6 steps
  • Zoom (+/-) Buttons
  • 3 steps

Flags

3

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

Bullets!

Better coordination with markups and the color/type of bullets will help make this guide more clear!

Markup Mishap

This guide needs better markups. Help out by correcting or making some markup annotations.

  • BackJVC Adixxion GC-XA1BU

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Find the side of the camera that looks like this.

Find the side of the camera that looks like this.

1024

Step 2

  • Push down on the black switch.

Push down on the black switch.

Step 3

  • While still pushing down on the black switch, slide back the battery cover (see photo for direction).

While still pushing down on the black switch, slide back the battery cover (see photo for direction).

Step 4

  • Push the cover up to open the battery compartment, and then push the blue battery release switch.

Push the cover up to open the battery compartment, and then push the blue battery release switch.

Step 5

  • You can now take the battery out of the camera.

You can now take the battery out of the camera.

Step 6

              Battery Cover
  • After removing the battery, take out the two Phillips screws (4mm headsize x 3mm length) screws. You can now remove the battery cover.

After removing the battery, take out the two Phillips screws (4mm headsize x 3mm length) screws. You can now remove the battery cover.

Step 7

              LCD Cover
  • Using a 1x1xH1.5 torx screwdriver, remove the 8 screws (5mm headsize / 4mm length) from the corners of both the front and back of the camera (4 screws on each side).

Using a 1x1xH1.5 torx screwdriver, remove the 8 screws (5mm headsize / 4mm length) from the corners of both the front and back of the camera (4 screws on each side).

Step 8

  • Carefully lift open the camera from the side of the device with the record and play buttons. Then remove the black cover tape by gently peeling it off. Make sure to save this tape as you may need it when you re-assemble the device.

Carefully lift open the camera from the side of the device with the record and play buttons. Then remove the black cover tape by gently peeling it off. Make sure to save this tape as you may need it when you re-assemble the device.

Step 9

  • Using the tweezers, carefully push up the left and right sides of the cable ribbon clip. Use the tweezers to life up and remove the clip.

Using the tweezers, carefully push up the left and right sides of the cable ribbon clip. Use the tweezers to life up and remove the clip.

Step 10

  • Using the tweezers, carefully remove the ribbon cable by gently grasping it and pulling up.

Using the tweezers, carefully remove the ribbon cable by gently grasping it and pulling up.

Step 11

  • Turn the camera 180 degrees, and gently remove the glue from the connector as shown in the photo. Make sure you save the glue as you may need it when re-assembling your device.

Turn the camera 180 degrees, and gently remove the glue from the connector as shown in the photo. Make sure you save the glue as you may need it when re-assembling your device.

Step 12

  • Now take out the connector by pulling the white clip out of the casing (as shown in the photos). This will will disconnect the screen from the main cable, allowing you to attach your new LCD cover.

Now take out the connector by pulling the white clip out of the casing (as shown in the photos). This will will disconnect the screen from the main cable, allowing you to attach your new LCD cover.

Step 13

              Zoom (+/-) Buttons
  • Remove the top two Phillips screws (4mm headsize x 3mm length). Now use the tweezers to gently grab and remove the silver metal plate that the screws were holding in place.

Remove the top two Phillips screws (4mm headsize x 3mm length). Now use the tweezers to gently grab and remove the silver metal plate that the screws were holding in place.

Step 14

  • Remove the bottom two Phillips screws (4mm headsize x 3mm length).

Remove the bottom two Phillips screws (4mm headsize x 3mm length).

Step 15

  • The zoom (+/-) buttons are attached to the red, black, and white threaded wire. Use the tweezers to gently pull on this wire and remove the zoom (+/-) buttons.

The zoom (+/-) buttons are attached to the red, black, and white threaded wire. Use the tweezers to gently pull on this wire and remove the zoom (+/-) buttons.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors 


                    Christina Michelle Johnson

Member since: 01/15/2015

1,023 Reputation

                                      8 Guides authored                  



                       Badges:
                       12







                                                        +9 more badges

Team

                       USF Tampa, Team 1-2, Tanski Winter 2015                        

                                                  Member of USF Tampa, Team 1-2, Tanski Winter 2015 



                    USFT-TANSKI-W15S1G2                     


                                            4 Members                     


                                            8 Guides authored