Difficulty

Moderate

Steps

4

Time Required

Suggest a time??

Sections

1

  • Brewing unit
  • 4 steps

Flags

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

  • BackJura Impressa Model Z repair.

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Brewing unit
  • Position the machine with the water tank side facing you.
  • The panel covering the brew group is fixed at the top edge with two oval head screws.
  • These screws have an oval head and look like rivets. They require a special tool or bit for unscrewing. Here is a DIY guide . In a pinch you can also use needle nosed pliers. Jura wants to keep us out of our own machines!
  • Remove the two oval head screws and lift the panel out.
  • There it is: the brewing unit.

Position the machine with the water tank side facing you.

The panel covering the brew group is fixed at the top edge with two oval head screws.

These screws have an oval head and look like rivets. They require a special tool or bit for unscrewing. Here is a DIY guide . In a pinch you can also use needle nosed pliers. Jura wants to keep us out of our own machines!

Remove the two oval head screws and lift the panel out.

There it is: the brewing unit.

1024

Step 2

  • The photo is from a Jura J5, but the brewing unit is basically the same and you can easily see how the brewing unit is attached:
  • Two Torx T20 screws with fine thread
  • One Torx T15 screw
  • The hot water inlet is plugged in.
  • The hose with the coffee spout is plugged on top.

The photo is from a Jura J5, but the brewing unit is basically the same and you can easily see how the brewing unit is attached:

Two Torx T20 screws with fine thread

One Torx T15 screw

The hot water inlet is plugged in.

The hose with the coffee spout is plugged on top.

Step 3

  • Unscrew the two Torx T15 machine screws.
  • Unscrew the Torx T15 screw at the bottom of the hot water inlet.
  • Pull the brewing unit out to you. The hose to the coffee spout is still attached at the top.
  • Pull off the hose to the coffee spout.

Unscrew the two Torx T15 machine screws.

Unscrew the Torx T15 screw at the bottom of the hot water inlet.

Pull the brewing unit out to you. The hose to the coffee spout is still attached at the top.

Pull off the hose to the coffee spout.

Step 4

  • Start now with the replacement or revision of the brewing unit.
  • If you want to disassemble the brewing unit for cleaning and installing new seals, follow this or this guides.
  • There is one small difference with this brewing group: the drainage valve is fitted with a cover, but this is easy to remove. Unscrew the two Torx T8 screws.
  • Use these instructions to overhaul the drainage valve.

Start now with the replacement or revision of the brewing unit.

If you want to disassemble the brewing unit for cleaning and installing new seals, follow this or this guides.

There is one small difference with this brewing group: the drainage valve is fitted with a cover, but this is easy to remove. Unscrew the two Torx T8 screws.

Use these instructions to overhaul the drainage valve.

Work through the steps in reverse order to reassemble your device.

Cancel: I did not complete this guide.

        These translators are helping us fix the world!      Want to contribute?      Start translating ›

Special thanks to these translators:

100%

VauWeh

oldturkey03

Author

                                      with 1 other contributor 


                    VauWeh

Member since: 10/19/2015

160,518 Reputation

                                      211 Guides authored                  



                       Badges:
                       41







                                                        +38 more badges