Difficulty

Moderate

Steps

10

Time Required

Suggest a time??

Sections

2

  • Opening the Jura Z series housing
  • 8 steps
  • Motor
  • 2 steps

Flags

1

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

  • BackJura Impressa Model Z repair.

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Opening the Jura Z series housing
  • Unplug the machine from the power outlet
  • Remove all attachments: water tank, drip tray, aroma lid

Unplug the machine from the power outlet

Remove all attachments: water tank, drip tray, aroma lid

1024

Step 2

  • Turn the machine so the back is facing toward the front.
  • The Jura sign must be removed. Turn it a few millimeters counterclickwise.
  • If this becomes difficult use a suction cup to assist.
  • Remove the Jura sign.

Turn the machine so the back is facing toward the front.

The Jura sign must be removed. Turn it a few millimeters counterclickwise.

If this becomes difficult use a suction cup to assist.

Remove the Jura sign.

Step 3

  • Behind the Jura sign are two screws with an oval head. They have to be removed.
  • These screws have an oval head that makes them look like rivets (picture 2). You need to use a special bit for their removal. If the right bit is not available, it could be done with a pair of needle nose pliers. Jura wants to keep us out of our own machines!!!!

Behind the Jura sign are two screws with an oval head. They have to be removed.

These screws have an oval head that makes them look like rivets (picture 2). You need to use a special bit for their removal. If the right bit is not available, it could be done with a pair of needle nose pliers. Jura wants to keep us out of our own machines!!!!

Step 4

  • Push the back down a bit and then remove it.

Push the back down a bit and then remove it.

Step 5

  • Pull the right side panel- as seen looking to the frontpanel - backwards and take it off.
  • Sometimes it gets a bit stuck and may require a bit more of a pull.

Pull the right side panel- as seen looking to the frontpanel - backwards and take it off.

Sometimes it gets a bit stuck and may require a bit more of a pull.

Step 6

  • In this step, you should remove the screws of the left side panel. The side panel can only be removed after removing the top cover.
  • Remove the Torx T15 screw on the front wall of the side panel.
  • In the side part there is a lid over the brew group. The lid is fastened at the top with two oval head screws. Remove those to remove the lid.
  • With the cover removed the brew group becomes visible

In this step, you should remove the screws of the left side panel. The side panel can only be removed after removing the top cover.

Remove the Torx T15 screw on the front wall of the side panel.

In the side part there is a lid over the brew group. The lid is fastened at the top with two oval head screws. Remove those to remove the lid.

With the cover removed the brew group becomes visible

Step 7

  • This step shows how to remove the top cover
  • Remove the powder tray and all coffee beans.
  • The cover is fastened with three Torx T15 screws. Those are easily visible under the covers as well as the small cover on the left back side.
  • Remove the two Phillips screws on the bean container and remove the bean container.
  • Lift the cover upwards.
  • If it is stuck, use a plastic opening tool to carefully pry it open.
  • The lid of the bean container is held in place by a small, strong magnet that loosely rests. It is either in the green marked recess, or it remains hanging on the bean container. Make sure it is not lost!

This step shows how to remove the top cover

Remove the powder tray and all coffee beans.

The cover is fastened with three Torx T15 screws. Those are easily visible under the covers as well as the small cover on the left back side.

Remove the two Phillips screws on the bean container and remove the bean container.

Lift the cover upwards.

If it is stuck, use a plastic opening tool to carefully pry it open.

The lid of the bean container is held in place by a small, strong magnet that loosely rests. It is either in the green marked recess, or it remains hanging on the bean container. Make sure it is not lost!

Step 8

  • Pull the left side panel backwards to take it off.
  • For some repairs it is not necessary to remove the left side panel.

Pull the left side panel backwards to take it off.

For some repairs it is not necessary to remove the left side panel.

Step 9

              Motor
  • The drive motor is fastened with two Torx T20 screws.
  • Remove the two screws.
  • Take out the motor
  • The encoder that counts the revolutions is located on the motor shaft. Disconnect the plug from the encoder

The drive motor is fastened with two Torx T20 screws.

Remove the two screws.

Take out the motor

The encoder that counts the revolutions is located on the motor shaft. Disconnect the plug from the encoder

Step 10

  • The motor is only connected with two cables. If you want to replace it completely, you have to follow the cables and disconnect them. You can also cut them and solder them, but make sure that they are well insulated, e.g. with heat shrink tubing.

The motor is only connected with two cables. If you want to replace it completely, you have to follow the cables and disconnect them. You can also cut them and solder them, but make sure that they are well insulated, e.g. with heat shrink tubing.

Work through the steps in reverse order to reassemble your device.

Cancel: I did not complete this guide.

        shingle is helping us fix the world!      Want to contribute?      Start translating ›

Special thanks to these translators:

100%

shingle

Author

                                      with 1 other contributor 


                    VauWeh

Member since: 10/19/2015

160,518 Reputation

                                      211 Guides authored                  



                       Badges:
                       41







                                                        +38 more badges