Difficulty
Difficult
Steps
12
Time Required
25 minutes
Sections
2
- Motherboard
- 7 steps
- Headphone Jacks
- 5 steps
Flags
1
Action Shots
Be an action hero! This guide needs images that better demonstrate how to perform specific actions.
BackJumper AngelSounds JPD-100S
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
During the replacement of the headphone jacks, you will locate them on the back of the motherboard, desolder the joints keeping the jacks in place, and remove them.
What you need
Step 1
Motherboard
- Access the battery compartment
- Remove the battery compartment lid and set it aside.
- Disconnect the battery and set it aside.
Access the battery compartment
Remove the battery compartment lid and set it aside.
Disconnect the battery and set it aside.
1024
Step 2
- Puncture the sticker in the battery compartment with a spudger to access the screw beneath it.
Puncture the sticker in the battery compartment with a spudger to access the screw beneath it.
Step 3
- Remove the 7mm Phillips #1 screw from the battery compartment.
- Place the screw in a secure place.
Remove the 7mm Phillips #1 screw from the battery compartment.
Place the screw in a secure place.
Step 4
- Begin prying open the device.
- Insert a plastic opening tool into the side groove about 2cm from the pink plastic component and pry open one side of the device.
- Once the side is separated, leave the opening tool inside to prevent the two sides from closing.
Begin prying open the device.
Insert a plastic opening tool into the side groove about 2cm from the pink plastic component and pry open one side of the device.
Once the side is separated, leave the opening tool inside to prevent the two sides from closing.
Step 5
- Insert another plastic opening tool into the groove opposite to the side of the tool already inserted.
- Create separation on that side until the white plastic component comes off entirely.
- Place the white plastic component in a secure place.
Insert another plastic opening tool into the groove opposite to the side of the tool already inserted.
Create separation on that side until the white plastic component comes off entirely.
Place the white plastic component in a secure place.
Step 6
- With your hand, remove the pink component.
With your hand, remove the pink component.
Step 7
- Remove the 7mm Phillips #1 screw in the middle of the motherboard.
Remove the 7mm Phillips #1 screw in the middle of the motherboard.
Step 8
Headphone Jacks
- Take the battery connector out of the battery compartment.
Take the battery connector out of the battery compartment.
Step 9
- Preheat the soldering iron .
- Locate the wires that connect to the transducer.
- Use a soldering iron and solder vacuum to unsolder the wires connected to the transducer.
Preheat the soldering iron .
Locate the wires that connect to the transducer.
Use a soldering iron and solder vacuum to unsolder the wires connected to the transducer.
Step 10
- Place the motherboard in a position that allows easy access to the jacks.
Place the motherboard in a position that allows easy access to the jacks.
Step 11
- Desolder the three solder joints securing each of the headphone jacks.
- Try not to melt the motherboard when removing solder that secures the jacks.
Desolder the three solder joints securing each of the headphone jacks.
Try not to melt the motherboard when removing solder that secures the jacks.
Step 12
- Remove the jacks by pulling them out of the motherboard.
Remove the jacks by pulling them out of the motherboard.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 2 other contributors
Yessika Lugo
Member since: 08/31/2015
113 Reputation
1 Guide authored
Badges:
4
+1 more badge
Team
USF Tampa, Team 6-1, Remmell Fall 2015
Member of USF Tampa, Team 6-1, Remmell Fall 2015
USFT-REMMELL-F15S6G1
6 Members
6 Guides authored
