Difficulty

Difficult

Steps

10

Time Required

                          20 minutes

Sections

2

  • Motherboard
  • 7 steps
  • Battery Cable
  • 3 steps

Flags

1

Action Shots

Be an action hero! This guide needs images that better demonstrate how to perform specific actions.

  • BackJumper AngelSounds JPD-100S

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

During the replacement of the battery cables, you will locate the battery cables on motherboard, unsolder the battery cable leads from the motherboard, and remove the battery cables.

What you need

Step 1

              Motherboard
  • Access the battery compartment
  • Remove the battery compartment lid and set it aside.
  • Disconnect the battery and set it aside.

Access the battery compartment

Remove the battery compartment lid and set it aside.

Disconnect the battery and set it aside.

1024

Step 2

  • Puncture the sticker in the battery compartment with a spudger to access the screw beneath it.

Puncture the sticker in the battery compartment with a spudger to access the screw beneath it.

Step 3

  • Remove the 7mm Phillips #1 screw from the battery compartment.
  • Place the screw in a secure place.

Remove the 7mm Phillips #1 screw from the battery compartment.

Place the screw in a secure place.

Step 4

  • Begin prying open the device.
  • Insert a plastic opening tool into the side groove about 2cm from the pink plastic component and pry open one side of the device.
  • Once the side is separated, leave the opening tool inside to prevent the two sides from closing.

Begin prying open the device.

Insert a plastic opening tool into the side groove about 2cm from the pink plastic component and pry open one side of the device.

Once the side is separated, leave the opening tool inside to prevent the two sides from closing.

Step 5

  • Insert another plastic opening tool into the groove opposite to the side of the tool already inserted.
  • Create separation on that side until the white plastic component comes off entirely.
  • Place the white plastic component in a secure place.

Insert another plastic opening tool into the groove opposite to the side of the tool already inserted.

Create separation on that side until the white plastic component comes off entirely.

Place the white plastic component in a secure place.

Step 6

  • With your hand, remove the pink component.

With your hand, remove the pink component.

Step 7

  • Remove the 7mm Phillips #1 screw in the middle of the motherboard.

Remove the 7mm Phillips #1 screw in the middle of the motherboard.

Step 8

              Battery Cable
  • Preheat soldering iron.
  • Locate the battery cable leads on the motherboard.

Preheat soldering iron.

Locate the battery cable leads on the motherboard.

Step 9

  • Use a soldering iron and solder vacuum to unsolder the battery cable leads.

Use a soldering iron and solder vacuum to unsolder the battery cable leads.

Step 10

  • Remove the battery cables by pulling them out of the motherboard.

Remove the battery cables by pulling them out of the motherboard.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors 


                    Safiyah Junaid

Member since: 08/31/2015

125 Reputation

                                      1 Guide authored                  



                       Badges:
                       11







                                                        +8 more badges

Team

                       USF Tampa, Team 6-1, Remmell Fall 2015                        

                                                  Member of USF Tampa, Team 6-1, Remmell Fall 2015 



                    USFT-REMMELL-F15S6G1                     


                                            6 Members                     


                                            6 Guides authored