Difficulty
Moderate
Steps
9
Time Required
10 - 15 minutes
Sections
1
- Electric Motor Wire
- 9 steps
Flags
0
BackCD Player
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Electric Motor Wire
- Place the CD player face up on a clean surface.
Place the CD player face up on a clean surface.
1024
Step 2
- Upturn the CD player and take out the batteries.
- To take out the batteries, pull back and lift the battery cover.
- Ensure that the batteries are properly removed, at this step.
Upturn the CD player and take out the batteries.
To take out the batteries, pull back and lift the battery cover.
Ensure that the batteries are properly removed, at this step.
Step 3
- Flip the CD player back and open the lid. You will see two 10 mm Phillips screws on the left and right side under the lid.
- To open the lid, push the button on the far right with an ejection symbol. Once the button is pushed, carefully lift the lid.
Flip the CD player back and open the lid. You will see two 10 mm Phillips screws on the left and right side under the lid.
To open the lid, push the button on the far right with an ejection symbol. Once the button is pushed, carefully lift the lid.
Step 4
- Unscrew each 10 mm Phillips screw with the screwdriver, and place them outside safely.
- Note the order in which you took the screws out.
Unscrew each 10 mm Phillips screw with the screwdriver, and place them outside safely.
Note the order in which you took the screws out.
Step 5
- Turn the CD player upside down and open the battery compartment. You will see one more 10 mm Phillips screw inside. Unscrew it.
- Use the Phillips screwdriver to remove the screw. Place the screw outside safely.
Turn the CD player upside down and open the battery compartment. You will see one more 10 mm Phillips screw inside. Unscrew it.
Use the Phillips screwdriver to remove the screw. Place the screw outside safely.
Step 6
- Now, open the CD player, and check the components inside.
- Be careful as this step requires some force.
Now, open the CD player, and check the components inside.
Be careful as this step requires some force.
Step 7
- Locate the motor on the bottom portion of the CD player. Lift the motor up and turn it over.
- Operate the motor carefully, since it is still connected to some wires.
Locate the motor on the bottom portion of the CD player. Lift the motor up and turn it over.
Operate the motor carefully, since it is still connected to some wires.
Step 8
- Locate these two small wires.
- Check whether both the wires are connected to the electric motor. If not, that is a probable reason why the CDs are not spinning once the device is turned on.
Locate these two small wires.
Check whether both the wires are connected to the electric motor. If not, that is a probable reason why the CDs are not spinning once the device is turned on.
Step 9
- Resolder the disconnected wires. This is a lengthy procedure.
- Be cautious, as the soldering iron is hot and may cause skin burns.
- Make sure to wash your hands after dealing with the solder.
Resolder the disconnected wires. This is a lengthy procedure.
Be cautious, as the soldering iron is hot and may cause skin burns.
Make sure to wash your hands after dealing with the solder.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 4 other contributors
Garrik Kaufman
Member since: 05/31/2016
148 Reputation
1 Guide authored
Badges:
5
+2 more badges
Team
Central Coast New Tech High, Team 6-2, Rushing Spring 2016
Member of Central Coast New Tech High, Team 6-2, Rushing Spring 2016
CCNTH-RUSHING-S16S6G2
2 Members
1 Guide authored
