Difficulty

Moderate

Steps

6

Time Required

                          15 minutes

Sections

1

  • Battery
  • 6 steps

Flags

2

Confusing Text

Some of this guide’s text is confusing, duplicated, or off-topic. Clarify it by editing!

Better Introduction

Improve this guide by completing or revising its introduction.

  • BackJBL Xtreme 3

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

Warning: please be aware of a potential swollen batteries, as this hyperlink will provide insight on what to look for.

What you need

Step 1

              Battery
  • Find the seam on the speaker and position it upwards.
  • Begin by turning the device to where the bottom side with groves are facing towards you. Use a spudger to carefully pry open and unlatch the side of the outer shell.
  • After they are unlatched, you should be able to open the shell by hand.

Find the seam on the speaker and position it upwards.

Begin by turning the device to where the bottom side with groves are facing towards you. Use a spudger to carefully pry open and unlatch the side of the outer shell.

After they are unlatched, you should be able to open the shell by hand.

1024

Step 2

  • Use a Phillips #0 screwdriver to remove the two 1 cm screws shown in the picture.

Use a Phillips #0 screwdriver to remove the two 1 cm screws shown in the picture.

Step 3

  • Use a spudger to slowly pop the shell off.
  • There is one nudge in the center below the power and Bluetooth button that should pop off.
  • Once you have unlatched this piece correctly, the shell will remove itself from the speaker itself.

Use a spudger to slowly pop the shell off.

There is one nudge in the center below the power and Bluetooth button that should pop off.

Once you have unlatched this piece correctly, the shell will remove itself from the speaker itself.

Step 4

  • Turn the device until the power and Bluetooth controls are facing down, and you will see a rectangular panel containing 8 screws.
  • Use a Phillips #1 screwdriver to remove the 8 1 cm screws.
  • Once all screws have been removed, carefully remove the panel.

Turn the device until the power and Bluetooth controls are facing down, and you will see a rectangular panel containing 8 screws.

Use a Phillips #1 screwdriver to remove the 8 1 cm screws.

Once all screws have been removed, carefully remove the panel.

Step 5

  • To remove the battery carefully use the (5) spudger to prop the battery out of its place. Ensure not to puncture the battery the removal of the battery should gently release with minimum effort.
  • Once the battery releasing be aware that it is still attached to a cable so do not tug or pull on the battery.

To remove the battery carefully use the (5) spudger to prop the battery out of its place. Ensure not to puncture the battery the removal of the battery should gently release with minimum effort.

Once the battery releasing be aware that it is still attached to a cable so do not tug or pull on the battery.

Step 6

  • Use an opening tool to push the small white lever piece. Depending on orientation of the speaker, the white lever should be pressed in the shortest direction towards are nearest wall of the speaker. In this particular orientation this it should be pushing in the north direction.
  • When removing the battery it would be advised to use the plastic opening tool to press the white notch north, simultaneously you will want to carefully pull the battery to unplug it.
  • Once the battery has been removed you may plug in the replacement.
  • Make sure the new battery is secure. Turn on the device to ensure that the battery is connected properly.

Use an opening tool to push the small white lever piece. Depending on orientation of the speaker, the white lever should be pressed in the shortest direction towards are nearest wall of the speaker. In this particular orientation this it should be pushing in the north direction.

When removing the battery it would be advised to use the plastic opening tool to press the white notch north, simultaneously you will want to carefully pull the battery to unplug it.

Once the battery has been removed you may plug in the replacement.

Make sure the new battery is secure. Turn on the device to ensure that the battery is connected properly.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 


                    Maria

Member since: 09/16/2022

351 Reputation

                                      3 Guides authored                  



                       Badges:
                       4







                                                        +1 more badge

Team

                       Western Carolina University, Team 1-2, Virtue Fall 2022                        

                                                  Member of Western Carolina University, Team 1-2, Virtue Fall 2022 



                    WCU-VIRTUE-F22S1G2                     


                                            4 Members                     


                                            5 Guides authored