Jbl Pulse 2 Auxiliary And Micro Usb Port Replacements Repair Guide

Difficulty

Moderate

Steps

Time Required

                          35 minutes

Sections

Battery
15 steps
Auxiliary and Micro USB Port
1 step

Flags

BackJBL Pulse 2
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Remove the rubber rings from either end of the device.
If there is difficulty in lifting the rings from the device, use the metal spudger.

Remove the rubber rings from either end of the device.

If there is difficulty in lifting the rings from the device, use the metal spudger.

1024

Step 2

Remove the four 4.8mm Phillips #1 screws from each end of the device with the Phillips head screwdriver.
Lift the end pieces off of the device.

Remove the four 4.8mm Phillips #1 screws from each end of the device with the Phillips head screwdriver.

Lift the end pieces off of the device.

Step 3

Remove the four 9.5mm Phillips #1 screws from each end of the device.

Remove the four 9.5mm Phillips #1 screws from each end of the device.

Step 4

Peel one end off and slowly draw it across the length of the device until you get to the other side.

Peel one end off and slowly draw it across the length of the device until you get to the other side.

Step 5

Remove the four 7.9mm Phillips #1 screws along the black centerpiece of the device between the camera and the auxiliary port.
Lift up the casing and circuit board but do not try and remove the ribbon wires.

Remove the four 7.9mm Phillips #1 screws along the black centerpiece of the device between the camera and the auxiliary port.

Lift up the casing and circuit board but do not try and remove the ribbon wires.

Step 6

Remove the cover from the end that the ribbon wires are attached to. It should peel off easily.

Remove the cover from the end that the ribbon wires are attached to. It should peel off easily.

Step 7

Unlatch the mechanism holding the ribbon wires in place, then disconnect them from the motherboard.
To access the wires, remove some of the black glue holding them in place with the spudger.

Unlatch the mechanism holding the ribbon wires in place, then disconnect them from the motherboard.

To access the wires, remove some of the black glue holding them in place with the spudger.

Step 8

Slowly pull the ribbon wires out from the outside.
If there is too much resistance, remove more of the black glue.

Slowly pull the ribbon wires out from the outside.

If there is too much resistance, remove more of the black glue.

Step 9

Remove the four 7.9mm Phillips #1 screws around the edges of the center piece.
Slide the outer casing off away from the auxiliary and micro USB port.

Remove the four 7.9mm Phillips #1 screws around the edges of the center piece.

Slide the outer casing off away from the auxiliary and micro USB port.

Step 10

Remove the other end of the device to access the wiring underneath it.

Remove the other end of the device to access the wiring underneath it.

Step 11

Use the angled tweezers to disconnect the battery from the motherboard. It will take some work to remove this piece.

Use the angled tweezers to disconnect the battery from the motherboard. It will take some work to remove this piece.

Step 12

Remove the four 7.9mm Phillips #1 screws from the black centerpiece of the device.

Remove the four 7.9mm Phillips #1 screws from the black centerpiece of the device.

Step 13

Use the spudger to reach under the sides of the black centerpiece to access the six latches, three of which are on each side.

Use the spudger to reach under the sides of the black centerpiece to access the six latches, three of which are on each side.

Step 14

Lift the black centerpiece off with the metal spudger to reveal the battery underneath.

Lift the black centerpiece off with the metal spudger to reveal the battery underneath.

Step 15

Use a hot air gun to soften the hot glue in order to fully remove the battery.

Use a hot air gun to soften the hot glue in order to fully remove the battery.

Step 16

              Auxiliary and Micro USB Port

Remove the solder on the micro USB and Auxiliary port wires to disconnect them.

Remove the solder on the micro USB and Auxiliary port wires to disconnect them.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      12 other people completed this guide.

Author

                                      with 3 other contributors

                    Emilee Hicks

Member since: 08/31/2018

668 Reputation

                                      3 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       Western Carolina University, Team S1-G1, Virtue Fall 2018                        

                                                  Member of Western Carolina University, Team S1-G1, Virtue Fall 2018 



                    WCU-VIRTUE-F18S1G1                     


                                            4 Members                     


                                            5 Guides authored

thetjfree - Sep 13, 2019

Can anyone post a link to buy the correct replacement micro USB port?

Thanks

Stephen Beale - Sep 14, 2019

https://smile.amazon.com/gp/product/B07T…

a_mostafa_k - Feb 21, 2021

Is there a video out there to demonstrate this repair process?

Roweda Johannes - Feb 10, 2022

Hallo, suche für die “JBL pulse 2” die Bauteile FB5 und D9 auf dem Mainboard.

Wer kennt diese Bauteile ?

Würde mich auf eine positive Antwort freuen.

Liebe Grüße J.R.

william.avril132 - Jun 26, 2022

Bonjour pourriez-vous me dire ou acheter cette petite carte électronique merci.

Introduction#

What you need#

Team#

Introduction

What you need

Team