Difficulty

Moderate

Steps

8

Time Required

                          5 - 8 minutes

Sections

4

  • Speaker Grill
  • 1 step
  • Speaker Housing
  • 3 steps
  • Carabiner Clip
  • 1 step
  • Motherboard
  • 3 steps

Flags

1

Better Introduction

Improve this guide by completing or revising its introduction.

  • BackJBL Clip 3

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

What you need

Step 1

              Speaker Grill
  • Insert the iFixit opening tool between the speaker grill and speaker housing and pry around the entire perimeter of the device until the grill releases.
  • A strong adhesive attaches the grill to the housing, and requires some time and patience to break. Use mild heat to loosen the adhesive if necessary.

Insert the iFixit opening tool between the speaker grill and speaker housing and pry around the entire perimeter of the device until the grill releases.

A strong adhesive attaches the grill to the housing, and requires some time and patience to break. Use mild heat to loosen the adhesive if necessary.

1024

Step 2

              Speaker Housing
  • Use a Phillips #1 screwdriver to remove the five 6.3 mm screws around the perimeter.

Use a Phillips #1 screwdriver to remove the five 6.3 mm screws around the perimeter.

Step 3

  • Separate the speaker housing from the rest of the body.
  • This requires minimal force; they are not glued together.

Separate the speaker housing from the rest of the body.

This requires minimal force; they are not glued together.

Step 4

  • Use tweezers to remove the 2 pin and 4 pin connectors from the motherboard.

Use tweezers to remove the 2 pin and 4 pin connectors from the motherboard.

Step 5

              Carabiner Clip
  • Lift the metal carabiner clip from the speaker housing.
  • They are not glued together and should separate easily.
  • There are alignment tabs on the clip so the whole assembly will only reassemble in one orientation.

Lift the metal carabiner clip from the speaker housing.

They are not glued together and should separate easily.

There are alignment tabs on the clip so the whole assembly will only reassemble in one orientation.

Step 6

              Motherboard
  • Use a pair of tweezers to release the two cable connections from the motherboard.
  • The wires connecting to the battery are not very long, so be careful when removing them.

Use a pair of tweezers to release the two cable connections from the motherboard.

The wires connecting to the battery are not very long, so be careful when removing them.

Step 7

  • Use a Phillips #1 screwdriver to remove the four screws.

Use a Phillips #1 screwdriver to remove the four screws.

Step 8

  • Lift the motherboard away from the speaker housing.
  • Desolder the two contact points.

Lift the motherboard away from the speaker housing.

Desolder the two contact points.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 4 other contributors 


                    Tyler Molden

Member since: 03/28/2022

420 Reputation

                                      4 Guides authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       UMass Dartmouth, Team 1-5, Petersen Spring 2022                        

                                                  Member of UMass Dartmouth, Team 1-5, Petersen Spring 2022 



                    UMASSD-PETERSEN-S22S1G5                     


                                            3 Members                     


                                            6 Guides authored