Jbl Charge Speaker Replacement Repair Guide

Difficulty

Easy

Steps

Time Required

                          5 - 7 minutes

Sections

Disassembling JBL Charge Casing
7 steps
Motherboard
4 steps
Speaker
4 steps

Flags

Incorrect Tools

Help make this guide better by using the correct tools in images and/or text.

BackJBL Charge
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Disassembling JBL Charge Casing

Make sure the device is powered off before you begin to disassemble the speaker.
Remove the trim from the speaker using a jimmy or metal spudger.

Make sure the device is powered off before you begin to disassemble the speaker.

Remove the trim from the speaker using a jimmy or metal spudger.

1024

Step 2

Use the PH1 screwdriver to remove all five of the 6 mm screws from the battery cover.
Remove the battery cover and set the cover aside.

Use the PH1 screwdriver to remove all five of the 6 mm screws from the battery cover.

Remove the battery cover and set the cover aside.

Step 3

Use a spudger to carefully remove the liquid electrical tape that holds the battery inside the battery compartment.
Be careful not to puncture the battery, or damage the battery wire underneath the liquid electrical tape.

Use a spudger to carefully remove the liquid electrical tape that holds the battery inside the battery compartment.

Be careful not to puncture the battery, or damage the battery wire underneath the liquid electrical tape.

Step 4

Use a nylon spudger to lift the battery out of the device.
Lift the end of the battery that does not have the wire connection and remove the 16 mm PH2 screw underneath the battery.
Notice the wire that is connecting the battery to the device. Attempting to remove the battery completely could cause damage to the wire. Do not use a metal spudger to remove the battery, this could cause damage.

Use a nylon spudger to lift the battery out of the device.

Lift the end of the battery that does not have the wire connection and remove the 16 mm PH2 screw underneath the battery.

Notice the wire that is connecting the battery to the device. Attempting to remove the battery completely could cause damage to the wire. Do not use a metal spudger to remove the battery, this could cause damage.

Step 5

Remove the four 16 mm screws from the white plastic casing using the PH2 screwdriver.

Remove the four 16 mm screws from the white plastic casing using the PH2 screwdriver.

Step 6

Starting in a corner of the device where the casing and the side meet, use a pointed metal spudger to pry the back casing off the speaker and the glue holding the seam together.
Slide the metal spudger along the seam to separate the back casing from the rest of the speaker.

Starting in a corner of the device where the casing and the side meet, use a pointed metal spudger to pry the back casing off the speaker and the glue holding the seam together.

Slide the metal spudger along the seam to separate the back casing from the rest of the speaker.

Step 7

Once the back casing is open, disconnect the three white connectors from the motherboard.
Remove the upper casing.

Once the back casing is open, disconnect the three white connectors from the motherboard.

Remove the upper casing.

Step 8

              Motherboard

Remove the 9 mm Phillips screw in the corner of the motherboard.

Remove the 9 mm Phillips screw in the corner of the motherboard.

Step 9

Remove the motherboard from the casing by lifting the corner of the board out of the device.
If the motherboard won’t budge, be sure that the square component on the bottom of the motherboard clears the edge of the speaker.
During reassembly, make sure the motherboard is fully installed and not sticking up past its original position, as this could damage the motherboard.

Remove the motherboard from the casing by lifting the corner of the board out of the device.

If the motherboard won’t budge, be sure that the square component on the bottom of the motherboard clears the edge of the speaker.

During reassembly, make sure the motherboard is fully installed and not sticking up past its original position, as this could damage the motherboard.

Step 10

Disconnect the two white connectors from the bottom of the motherboard.

Disconnect the two white connectors from the bottom of the motherboard.

Step 11

Pull down on the black clip holding the ribbon cable in place.
Pull the ribbon cable from the connector using the blue tab.
Remove the motherboard from the device.

Pull down on the black clip holding the ribbon cable in place.

Pull the ribbon cable from the connector using the blue tab.

Remove the motherboard from the device.

Step 12

              Speaker

Using the PH1 screwdriver, remove the 9mm Phillips screw that connects the black tube to the device’s interior.

Using the PH1 screwdriver, remove the 9mm Phillips screw that connects the black tube to the device’s interior.

Step 13

Slowly but firmly pull the grey cap off the device. This will provide complete access to the speakers.

Slowly but firmly pull the grey cap off the device. This will provide complete access to the speakers.

Step 14

Each speaker is held in place with two 9mm Phillips screws. Remove the screws using the PH1 screwdriver head.
If you are replacing the left speaker, remove the screws and speaker on your right.
If you are replacing the right speaker, remove the screws and speaker on your left.

Each speaker is held in place with two 9mm Phillips screws. Remove the screws using the PH1 screwdriver head.

If you are replacing the left speaker, remove the screws and speaker on your right.

If you are replacing the right speaker, remove the screws and speaker on your left.

Step 15

Pull the speaker out of the casing.

Pull the speaker out of the casing.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      14 other people completed this guide.

Author

                                      with 6 other contributors

                    Alexander Castanares

Member since: 04/01/2015

855 Reputation

                                      2 Guides authored                  



                       Badges:
                       21







                                                        +18 more badges

Team

                       Cal Poly, Team 12-4, Lancaster Spring 2015                        

                                                  Member of Cal Poly, Team 12-4, Lancaster Spring 2015 



                    CPSU-LANCASTER-S15S12G4                     


                                            2 Members                     


                                            17 Guides authored

feliper233 - Feb 26, 2016

Donde encuentro las bocinas no sirven la que tiene

Donde puedo conseguir las bocinas?

rohit jayendra - Mar 5, 2016

Where can I get gthe replacement speaker?

tamaerocksxd - Apr 20, 2016

where can i get replaicment speaker?

Robert - May 31, 2016

Where do I get the replacement speakers

Incorrect Tools#

Introduction#

What you need#

Team#

Incorrect Tools

Introduction

What you need

Team