Difficulty
Moderate
Steps
10
Time Required
30 - 40 minutes
Sections
2
- Outer Case
- 7 steps
- Battery
- 3 steps
Flags
0
BackJawbone Big Jambox
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Outer Case
- Remove both end caps by putting a plastic opening tool in the center of the seam. Work around the edges to pry the end caps off completely.
- Due to interior clips holding the end caps in place, use caution when applying force.
Remove both end caps by putting a plastic opening tool in the center of the seam. Work around the edges to pry the end caps off completely.
Due to interior clips holding the end caps in place, use caution when applying force.
1024
Step 2
- Turn the Jambox upside down. Peel the indicated rubber tabs off, using a plastic opening tool if necessary.
- You may want to only take the tabs half way off to avoid re-gluing when reassembling.
- Remove the three T6, 7.0 mm screws under each rubber tab.
- Because the screws are a different length, set the screws aside.
Turn the Jambox upside down. Peel the indicated rubber tabs off, using a plastic opening tool if necessary.
You may want to only take the tabs half way off to avoid re-gluing when reassembling.
Remove the three T6, 7.0 mm screws under each rubber tab.
Because the screws are a different length, set the screws aside.
Step 3
- With the Jawbone logo facing towards you and with correct orientation, place the Jambox with the left end cap facing upward.
- Unscrew indicated T6 9.7 mm screws.
- Gently loosen the tabs from their anchor points so the bottom may be removed.
- Flip the Jambox so the other end cap is facing up. The USB cable is on this side (metal grounding clip, indicated in orange). Repeat the above two steps.
With the Jawbone logo facing towards you and with correct orientation, place the Jambox with the left end cap facing upward.
Unscrew indicated T6 9.7 mm screws.
Gently loosen the tabs from their anchor points so the bottom may be removed.
Flip the Jambox so the other end cap is facing up. The USB cable is on this side (metal grounding clip, indicated in orange). Repeat the above two steps.
Step 4
- Pry up the bottom panel by lifting from the device.
- Pull the bottom up. This may take a bit of force as the bottom is glued to device.
- Once removed, the battery will now be visible.
Pry up the bottom panel by lifting from the device.
Pull the bottom up. This may take a bit of force as the bottom is glued to device.
Once removed, the battery will now be visible.
Step 5
- Before unscrewing, take a picture of the top view. That way, when you’re reassembling the device, you’ll know the orientation of the metal grounding plates.
- Unscrew the eight indicated T6 9.8 mm screws. Remove metal grounding plates.
Before unscrewing, take a picture of the top view. That way, when you’re reassembling the device, you’ll know the orientation of the metal grounding plates.
Unscrew the eight indicated T6 9.8 mm screws. Remove metal grounding plates.
Step 6
- Once all eight screws are removed, pry the sides of the Jambox to lift the body from it’s shell.
Once all eight screws are removed, pry the sides of the Jambox to lift the body from it’s shell.
Step 7
- With the battery facing forward, remove the three indicated T6 9.5 mm screws.
- Once the screws are removed, lift up the small plastic plate, revealing the auxiliary board underneath.
With the battery facing forward, remove the three indicated T6 9.5 mm screws.
Once the screws are removed, lift up the small plastic plate, revealing the auxiliary board underneath.
Step 8
Battery
- Remove the indicated T6, 7.4mm screw holding the auxiliary board in place.
- Carefully lift the circuit board up and off to the side.
Remove the indicated T6, 7.4mm screw holding the auxiliary board in place.
Carefully lift the circuit board up and off to the side.
Step 9
- Pull on the red and black cables under the auxiliary board to disconnect the battery.
Pull on the red and black cables under the auxiliary board to disconnect the battery.
Step 10
- The battery is connected to the Jambox by double stick tape. Use your finger to pry out the battery.
- Place a new battery in the old battery’s place. Reverse these steps to connect the new battery.
- When plugging in the new battery, ensure the red and black wires are separated around pegs so they are not pinched when the auxiliary board is replaced.
The battery is connected to the Jambox by double stick tape. Use your finger to pry out the battery.
Place a new battery in the old battery’s place. Reverse these steps to connect the new battery.
When plugging in the new battery, ensure the red and black wires are separated around pegs so they are not pinched when the auxiliary board is replaced.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
57 other people completed this guide.
Author
with 4 other contributors
Abby Cybula
Member since: 04/01/2015
1,753 Reputation
2 Guides authored
Badges:
19
+16 more badges
Team
Cal Poly, Team 24-5, Lancaster Spring 2015
Member of Cal Poly, Team 24-5, Lancaster Spring 2015
CPSU-LANCASTER-S15S24G5
4 Members
7 Guides authored
Kevin Foti - Mar 2, 2016
Reply
Where do I buy the battery.
Lin - Aug 31, 2017
http://www.ebay.com/itm/322588700358?ul_… :Here is someone who made and sell the battery for Jambox and Big Jambox, i hope this could be helpful
speedlexx - Mar 11, 2016
Reply
да где аккумулятор купить то?
Max - Mar 29, 2017
на рынке покупаются стандартные 18650 и меняются на старые акку из колонки. что б пошла зарядка нужно дать больше ток.
цена вопроса ~ 1200₽ с работой
Edward Brown - May 31, 2016
Reply
Where do I go to purchase a battery?
