Difficulty

Moderate

Steps

7

Time Required

                          10 - 15 minutes

Sections

2

  • Front Plate
  • 3 steps
  • Speaker
  • 4 steps

Flags

0

  • BackJabra CRUISER2

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Front Plate
  • Use the iOpener tool to unglue the adhesive of the device. The link to the iOpener instructions are listed below.
  • iOpener Instructions

Use the iOpener tool to unglue the adhesive of the device. The link to the iOpener instructions are listed below.

iOpener Instructions

1024

Step 2

  • Place the flat head of the bigger plastic opening tool in between the front plate and back plate.
  • Pull the tool toward the back of the device to pry it open.
  • Repeat this process over all edges of the device.

Place the flat head of the bigger plastic opening tool in between the front plate and back plate.

Pull the tool toward the back of the device to pry it open.

Repeat this process over all edges of the device.

Step 3

  • Open up the device by pulling the front plate straight up from the back plate.

Open up the device by pulling the front plate straight up from the back plate.

Step 4

              Speaker
  • Carefully unplug the red and black wires that run from the speaker to the motherboard by detaching the white connecting piece.

Carefully unplug the red and black wires that run from the speaker to the motherboard by detaching the white connecting piece.

Step 5

  • Using the PH000, unscrew the two 5.5mm screws attaching the speaker to the front plate.
  • The screwdriver sizes are located on the sides of their heads.

Using the PH000, unscrew the two 5.5mm screws attaching the speaker to the front plate.

The screwdriver sizes are located on the sides of their heads.

Step 6

  • Gently pull the black and red wires away from the back plate to remove the speaker.

Gently pull the black and red wires away from the back plate to remove the speaker.

Step 7

  • Carefully pull the wires away from the speaker, detaching them from the adhesive, while keeping the ends intact.

Carefully pull the wires away from the speaker, detaching them from the adhesive, while keeping the ends intact.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 


                    Spartacus

Member since: 10/17/2014

636 Reputation

                                      5 Guides authored                  



                       Badges:
                       14







                                                        +11 more badges

Team

                       Baylor, Team 8-13, Williams Fall 2014                        

                                                  Member of Baylor, Team 8-13, Williams Fall 2014 



                    BU-WILLIAMS-F14S8G13                     


                                            3 Members                     


                                            5 Guides authored

Brucereno2 - Mar 15, 2015

Reply

Is this a fairly standard speaker? With radio shack dead, can you suggest a source? Any specs? Yhanks

Scot Tetreault - Oct 14, 2019

Did you ever find a speaker for your jabra cruiser?

Frantisek Fridrich - Dec 6, 2019

Reply

halo

where i can get the new speaker for jabra cruiser 2?

Frantisek Fridrich - Dec 9, 2019

Reply

simple speaker in electronic parts shop 8ohm diameter 35mm price 1.2 €

Mobi - Feb 2, 2022

Reply

A 36 mm speaker will also fit nicely. A 1 watt 8 ohms speaker is the best choice - the amplifier is not able to output enough power to drive a 2+ watt speaker.