Iview 776Tpcii Camera Assembly Replacement Repair Guide

Difficulty

Easy

Steps

Time Required

                          5 - 10 minutes

Sections

Rear Panel
2 steps
Camera Assembly
3 steps

Flags

BackiView-776TPCII
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Rear Panel

Before disassembling your device, make sure that the power is completely turned off.
Use the plastic opening tool to release the clips holding the rear panel of the device onto the front section.
The clips may take some pressure before releasing.
Continue around the entire device until all of the clips have been released.

Before disassembling your device, make sure that the power is completely turned off.

Use the plastic opening tool to release the clips holding the rear panel of the device onto the front section.

The clips may take some pressure before releasing.

Continue around the entire device until all of the clips have been released.

1024

Step 2

Use a spudger to carefully free the speaker from it’s housing on the back panel.
Place the spudger between the speaker and the rear panel. Use a prying motion to remove the component.
Be careful not to apply an over amount of force. If care is not taken, the speaker could break under the pressure.

Use a spudger to carefully free the speaker from it’s housing on the back panel.

Place the spudger between the speaker and the rear panel. Use a prying motion to remove the component.

Be careful not to apply an over amount of force. If care is not taken, the speaker could break under the pressure.

Step 3

              Camera Assembly

The camera module is located in the upper-right corner of the tablet.
Loosen the edges of the black tape covering the camera using the heavy-duty spudger.
Use the freed edges of the tape to gently remove the camera assembly from its plastic housing.
The camera assembly will still be connected to the rest of the device via a ribbon cable. Take care so as not to tear this connection.

The camera module is located in the upper-right corner of the tablet.

Loosen the edges of the black tape covering the camera using the heavy-duty spudger.

Use the freed edges of the tape to gently remove the camera assembly from its plastic housing.

The camera assembly will still be connected to the rest of the device via a ribbon cable. Take care so as not to tear this connection.

Step 4

Use tweezers to lift the cover off the top of the camera’s ZIF adapter.
When reassembling the device, be sure to fully secure the ribbon cable from the camera back into the ZIF adapter.
Pull the assembly away from the motherboard with a set of tweezers to prepare for desoldering.

Use tweezers to lift the cover off the top of the camera’s ZIF adapter.

When reassembling the device, be sure to fully secure the ribbon cable from the camera back into the ZIF adapter.

Pull the assembly away from the motherboard with a set of tweezers to prepare for desoldering.

Step 5

Use the Portable Soldering Iron tool to heat the leads coming from the camera assembly to the motherboard, thereby breaking the connection.
For help on soldering, refer to the iFixit “How To Solder and Desolder Connections” technique guide as necessary.
Once heated, use tweezers to pull the wires free from their connections.
To ease reassembly, take note of which wire went to the positive and negative terminals.

Use the Portable Soldering Iron tool to heat the leads coming from the camera assembly to the motherboard, thereby breaking the connection.

For help on soldering, refer to the iFixit “How To Solder and Desolder Connections” technique guide as necessary.

Once heated, use tweezers to pull the wires free from their connections.

To ease reassembly, take note of which wire went to the positive and negative terminals.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors

                    Cory Gratzer

Member since: 09/16/2015

570 Reputation

                                      5 Guides authored                  



                       Badges:
                       17







                                                        +14 more badges

Team

                       IUPUI, Team 2-2, Baechle Fall 2015                        

                                                  Member of IUPUI, Team 2-2, Baechle Fall 2015 



                    IUPUI-BAECHLE-F15S2G2                     


                                            3 Members                     


                                            12 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team