Iview 754Tpc Logic Board Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

Suggest a time??

Sections

Rear Panel
1 step
Remove Battery
1 step
Camera Assembly
2 steps
Logic Board
5 steps

Flags

BackiVIEW-754TPC
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Rear Panel

Before disassembling your tablet, make sure it is powered off.
Use plastic opening tool to release the clips holding the device together. The clips will take a small amount of pressure to release. Once you have the plastic opening tool inserted, use a twisting action to release the clips. Start from bottom of device and work all the way around.

Before disassembling your tablet, make sure it is powered off.

Use plastic opening tool to release the clips holding the device together. The clips will take a small amount of pressure to release. Once you have the plastic opening tool inserted, use a twisting action to release the clips. Start from bottom of device and work all the way around.

1024

Step 2

              Remove Battery

Use flat side of the spudger to get under battery and use pressure to release from glue. Do this all the way around battery until it comes off.
At this point do not attempt to fully remove the battery as it is still attached to the logic board.

Use flat side of the spudger to get under battery and use pressure to release from glue. Do this all the way around battery until it comes off.

At this point do not attempt to fully remove the battery as it is still attached to the logic board.

Step 3

              Camera Assembly

The camera module is located directly under the top right corner of the back cover.
Peel back the tape holding down the camera ribbon connector using a pair of tweezers.
As you peel the tape backward, the front facing camera may come out, this is not an issue.
If the front facing camera does not come out, gently lift it out with a pair of tweezers

The camera module is located directly under the top right corner of the back cover.

Peel back the tape holding down the camera ribbon connector using a pair of tweezers.

As you peel the tape backward, the front facing camera may come out, this is not an issue.

If the front facing camera does not come out, gently lift it out with a pair of tweezers

Step 4

              Remove Camera

Use a spudger to lift flap on top of the camera ZIF adapter.
At this point the camera module can be easily removed with a pair of tweezers.
During reassembly, make sure you put the ZIF adapter snugly back into its socket and secure the flap.

Use a spudger to lift flap on top of the camera ZIF adapter.

At this point the camera module can be easily removed with a pair of tweezers.

During reassembly, make sure you put the ZIF adapter snugly back into its socket and secure the flap.

Step 5

              Logic Board

Remove the four 2.2mm Phillips screws holding the logic board in place. Place the screws on the iFixit magnetic project mat.

Remove the four 2.2mm Phillips screws holding the logic board in place. Place the screws on the iFixit magnetic project mat.

Step 6

              WIFI Antenna

Gently peel the WIFI Antenna up using a pair of tweezers.

Gently peel the WIFI Antenna up using a pair of tweezers.

Step 7

              Disconnect LCD

Use a spudger to lift the flap on top of the LCD ZIF socket.
Gently remove the ribbon cable from the socket using a tweezers.

Use a spudger to lift the flap on top of the LCD ZIF socket.

Gently remove the ribbon cable from the socket using a tweezers.

Step 8

              Disconnect Digitizer

Use a spudger to lift the flap on top of the digitizer ZIF socket.
Gently pull the tape attached to the ribbon cable to remove the cable from its socket.

Use a spudger to lift the flap on top of the digitizer ZIF socket.

Gently pull the tape attached to the ribbon cable to remove the cable from its socket.

Step 9

              Remove Logic Board

Gently slide the spudger below the logic board at the left side nearest the battery. Lift upward and away from the power button and bottom connectors.
The battery is still attached to the logic board. Be careful to not tear the two apart during removal.

Gently slide the spudger below the logic board at the left side nearest the battery. Lift upward and away from the power button and bottom connectors.

The battery is still attached to the logic board. Be careful to not tear the two apart during removal.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 1 other contributor

                    Robert Clark

Member since: 01/21/2015

1,065 Reputation

                                      7 Guides authored                  



                       Badges:
                       16







                                                        +13 more badges

Team

                       USF Tampa, Team 5-4, Brown Winter 2015                        

                                                  Member of USF Tampa, Team 5-4, Brown Winter 2015 



                    USFT-BROWN-W15S5G4                     


                                            4 Members                     


                                            16 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team