Difficulty
Moderate
Steps
10
Time Required
15 - 30 minutes
Sections
5
- Rear Panel
- 1 step
- Remove Battery
- 1 step
- Camera Assembly
- 2 steps
- Logic Board
- 5 steps
- LCD
- 1 step
Flags
0
BackiVIEW-754TPC
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Rear Panel
- Before disassembling your tablet, make sure it is powered off.
- Use plastic opening tool to release the clips holding the device together. The clips will take a small amount of pressure to release. Once you have the plastic opening tool inserted, use a twisting action to release the clips. Start from bottom of device and work all the way around.
Before disassembling your tablet, make sure it is powered off.
Use plastic opening tool to release the clips holding the device together. The clips will take a small amount of pressure to release. Once you have the plastic opening tool inserted, use a twisting action to release the clips. Start from bottom of device and work all the way around.
1024
Step 2
Remove Battery
- Use flat side of the spudger to get under battery and use pressure to release from glue. Do this all the way around battery until it comes off.
- At this point do not attempt to fully remove the battery as it is still attached to the logic board.
Use flat side of the spudger to get under battery and use pressure to release from glue. Do this all the way around battery until it comes off.
At this point do not attempt to fully remove the battery as it is still attached to the logic board.
Step 3
Camera Assembly
- The camera module is located directly under the top right corner of the back cover.
- Peel back the tape holding down the camera ribbon connector using a pair of tweezers.
- As you peel the tape backward, the front facing camera may come out, this is not an issue.
- If the front facing camera does not come out, gently lift it out with a pair of tweezers
The camera module is located directly under the top right corner of the back cover.
Peel back the tape holding down the camera ribbon connector using a pair of tweezers.
As you peel the tape backward, the front facing camera may come out, this is not an issue.
If the front facing camera does not come out, gently lift it out with a pair of tweezers
Step 4
Remove Camera
- Use a spudger to lift flap on top of the camera ZIF adapter.
- At this point the camera module can be easily removed with a pair of tweezers.
- During reassembly, make sure you put the ZIF adapter snugly back into its socket and secure the flap.
Use a spudger to lift flap on top of the camera ZIF adapter.
At this point the camera module can be easily removed with a pair of tweezers.
During reassembly, make sure you put the ZIF adapter snugly back into its socket and secure the flap.
Step 5
Logic Board
- Remove the four 2.2mm Phillips screws holding the logic board in place. Place the screws on the iFixit magnetic project mat.
Remove the four 2.2mm Phillips screws holding the logic board in place. Place the screws on the iFixit magnetic project mat.
Step 6
WIFI Antenna
- Gently peel the WIFI Antenna up using a pair of tweezers.
Gently peel the WIFI Antenna up using a pair of tweezers.
Step 7
Disconnect LCD
- Use a spudger to lift the flap on top of the LCD ZIF socket.
- Gently remove the ribbon cable from the socket using a tweezers.
Use a spudger to lift the flap on top of the LCD ZIF socket.
Gently remove the ribbon cable from the socket using a tweezers.
Step 8
Disconnect Digitizer
- Use a spudger to lift the flap on top of the digitizer ZIF socket.
- Gently pull the tape attached to the ribbon cable to remove the cable from its socket.
Use a spudger to lift the flap on top of the digitizer ZIF socket.
Gently pull the tape attached to the ribbon cable to remove the cable from its socket.
Step 9
Remove Logic Board
- Gently slide the spudger below the logic board at the left side nearest the battery. Lift upward and away from the power button and bottom connectors.
- The battery is still attached to the logic board. Be careful to not tear the two apart during removal.
Gently slide the spudger below the logic board at the left side nearest the battery. Lift upward and away from the power button and bottom connectors.
The battery is still attached to the logic board. Be careful to not tear the two apart during removal.
Step 10
LCD
- Insert a plastic opening tool between the LCD and digitizer on the side of the LCD with the ribbon cable. Use a second plastic opening tool to lift the LCD from the digitizer. Repeat this process on both sides of the LCD ribbon cable.
- Fully remove the LCD from the digitizer.
Insert a plastic opening tool between the LCD and digitizer on the side of the LCD with the ribbon cable. Use a second plastic opening tool to lift the LCD from the digitizer. Repeat this process on both sides of the LCD ribbon cable.
Fully remove the LCD from the digitizer.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 1 other contributor
Robert Clark
Member since: 01/21/2015
1,065 Reputation
7 Guides authored
Badges:
16
+13 more badges
Team
USF Tampa, Team 5-4, Brown Winter 2015
Member of USF Tampa, Team 5-4, Brown Winter 2015
USFT-BROWN-W15S5G4
4 Members
16 Guides authored
