Ivation Ivwpdc20Y Motherboard Replacement Repair Guide

Difficulty

Very difficult

Steps

Time Required

                          1 - 3 hours

Sections

Motherboard
19 steps

Flags

BackIvation IVWPDC20Y
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Motherboard

With the H2.0 bit screwdriver, remove the two screws on the yellow waterproof cover

With the H2.0 bit screwdriver, remove the two screws on the yellow waterproof cover

1024

Step 2

Apply a plastic opening tool to each of the corners and gently remove the casing
The front casing is held down by adhesive and may require additional work to remove
Apply just enough force to undo the inner latches to make sure not to damage the waterproof seal

Apply a plastic opening tool to each of the corners and gently remove the casing

The front casing is held down by adhesive and may require additional work to remove

Apply just enough force to undo the inner latches to make sure not to damage the waterproof seal

Step 3

Remove the five silver screws from the inner casing using the PH00 screwdriver bit

Remove the five silver screws from the inner casing using the PH00 screwdriver bit

Step 4

Remove the six screws from the edge of the clear inner casing with the PH00 screwdriver bit
These screws are very small and easy to strip so apply consistent pressure when removing them

Remove the six screws from the edge of the clear inner casing with the PH00 screwdriver bit

These screws are very small and easy to strip so apply consistent pressure when removing them

Step 5

Pry off back outer casing using the black spudger or the blue prying tools

Pry off back outer casing using the black spudger or the blue prying tools

Step 6

Carefully remove the screen from the silver casing using a prying tool or the black spudger
There is adhesive in the center of the screen, be sure not to bend it when applying pressure

Carefully remove the screen from the silver casing using a prying tool or the black spudger

There is adhesive in the center of the screen, be sure not to bend it when applying pressure

Step 7

Gently push out the pins holding the orange tape down using the pointy end of the spudger
Screen and orange tape should slip out as a whole

Gently push out the pins holding the orange tape down using the pointy end of the spudger

Screen and orange tape should slip out as a whole

Step 8

Remove three screws holding the silver screen casing to the motherboard using the PH00 bit screwdriver

Remove three screws holding the silver screen casing to the motherboard using the PH00 bit screwdriver

Step 9

Remove three screws holding the motherboard into the casing using the PH00 bit screwdriver bit

Remove three screws holding the motherboard into the casing using the PH00 bit screwdriver bit

Step 10

Gently lift the corner of the motherboard out
Everything should come out as one component free of the casing

Gently lift the corner of the motherboard out

Everything should come out as one component free of the casing

Step 11

Remove the soldering on the three wires holding the flash bulb
The wires are different colors: red, white, and black

Remove the soldering on the three wires holding the flash bulb

The wires are different colors: red, white, and black

Step 12

Remove the two screws holding the lens assembly to the motherboard using the PH00 bit screwdriver

Remove the two screws holding the lens assembly to the motherboard using the PH00 bit screwdriver

Step 13

Remove the soldering on the 3 wires that are connected to the lens unit

Remove the soldering on the 3 wires that are connected to the lens unit

Step 14

Remove the three screws holding the button sensors to the battery casing using the PH00 screwdriver bit

Remove the three screws holding the button sensors to the battery casing using the PH00 screwdriver bit

Step 15

Remove soldering on the grouping of wires connecting the button sensors

Remove soldering on the grouping of wires connecting the button sensors

Step 16

Lift screen to reveal wires underneath
Remove soldering connecting screen to the motherboard

Lift screen to reveal wires underneath

Remove soldering connecting screen to the motherboard

Step 17

Gently pull orange tape from the motherboard

Gently pull orange tape from the motherboard

Step 18

Remove soldering from the two green wires connected to the motherboard

Remove soldering from the two green wires connected to the motherboard

Step 19

Gently bend the capacitor upwards
Remove soldering from the two connectors

Gently bend the capacitor upwards

Remove soldering from the two connectors

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 2 other contributors

                    Wendy Jones

Member since: 02/06/2016

225 Reputation

                                      2 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       USF Tampa, Team 6-6, Eyestone Spring 2016                        

                                                  Member of USF Tampa, Team 6-6, Eyestone Spring 2016 



                    USFT-EYESTONE-S16S6G6                     


                                            3 Members                     


                                            5 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team