Difficulty
Difficult
Steps
12
Time Required
30 minutes
Sections
1
- Lens Assembly
- 12 steps
Flags
0
BackIvation IVWPDC20Y
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Lens Assembly
- With the H2.0 bit screwdriver, remove the two screws on the yellow waterproof cover
With the H2.0 bit screwdriver, remove the two screws on the yellow waterproof cover
1024
Step 2
- Apply a plastic opening tool to each of the corners and gently remove the casing
- The front casing is held down by adhesive and may require additional work to remove
- Apply just enough force to undo the inner latches to make sure not to damage the waterproof seal
Apply a plastic opening tool to each of the corners and gently remove the casing
The front casing is held down by adhesive and may require additional work to remove
Apply just enough force to undo the inner latches to make sure not to damage the waterproof seal
Step 3
- Remove the five silver screws from the inner casing using the PH00 screwdriver bit
Remove the five silver screws from the inner casing using the PH00 screwdriver bit
Step 4
- Remove the six screws from the edge of the clear inner casing with the PH00 screwdriver bit
- These screws are very small and easy to strip so apply consistent pressure when removing them
Remove the six screws from the edge of the clear inner casing with the PH00 screwdriver bit
These screws are very small and easy to strip so apply consistent pressure when removing them
Step 5
- Pry off back outer casing using the black spudger or the blue prying tools
Pry off back outer casing using the black spudger or the blue prying tools
Step 6
- Carefully remove the screen from the silver casing using a prying tool or the black spudger
- There is adhesive in the center of the screen, be sure not to bend it when applying pressure
Carefully remove the screen from the silver casing using a prying tool or the black spudger
There is adhesive in the center of the screen, be sure not to bend it when applying pressure
Step 7
- Using the poker end of the spudger push gently on the black pegs holding the orange tape in place
- Screen and orange tape should slip out as a whole
Using the poker end of the spudger push gently on the black pegs holding the orange tape in place
Screen and orange tape should slip out as a whole
Step 8
- Remove three screws holding the silver screen casing to the motherboard using the PH00 bit screwdriver
Remove three screws holding the silver screen casing to the motherboard using the PH00 bit screwdriver
Step 9
- Remove three screws holding the motherboard into the casing using the PH00 bit screwdriver
Remove three screws holding the motherboard into the casing using the PH00 bit screwdriver
Step 10
- Gently lift the corner of the motherboard out
- Everything should come out as one component free of the casing
Gently lift the corner of the motherboard out
Everything should come out as one component free of the casing
Step 11
- Remove the two screws holding the lens assembly to the motherboard using the PH00 bit screwdriver
Remove the two screws holding the lens assembly to the motherboard using the PH00 bit screwdriver
Step 12
- Remove the soldering on the 3 wires that are connected to the lens unit
Remove the soldering on the 3 wires that are connected to the lens unit
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 3 other contributors
Jack Schlandt
Member since: 02/08/2016
197 Reputation
1 Guide authored
Badges:
11
+8 more badges
Team
USF Tampa, Team 6-6, Eyestone Spring 2016
Member of USF Tampa, Team 6-6, Eyestone Spring 2016
USFT-EYESTONE-S16S6G6
3 Members
5 Guides authored
