Ipod Shuffle 1St Generation Usb Port Replacement Repair Guide

Difficulty

Difficult

Steps

Time Required

Suggest a time??

Sections

Hold Switch
2 steps
Casing
7 steps
USB Port
3 steps

Flags

BackiPod Shuffle 1st Generation
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Hold Switch

Before opening your iPod, ensure that the hold switch is in the locked position.

Before opening your iPod, ensure that the hold switch is in the locked position.

1024

Step 2

Use a spudger to pry up the white plastic hold switch.

Use a spudger to pry up the white plastic hold switch.

Step 3

              Casing

If present, remove the cap from the USB port.

If present, remove the cap from the USB port.

Step 4

The following step can be challenging and time consuming. Be sure to go slowly and have patience to prevent damaging your iPod.
Use an Exacto knife to separate the glue holding the USB port on the iPod. Run the knife along the seam between the two sections of the iPod until the glue is separated. Expect to run the knife along this edge 20-30 times before the glue will be entirely freed.

The following step can be challenging and time consuming. Be sure to go slowly and have patience to prevent damaging your iPod.

Use an Exacto knife to separate the glue holding the USB port on the iPod. Run the knife along the seam between the two sections of the iPod until the glue is separated. Expect to run the knife along this edge 20-30 times before the glue will be entirely freed.

Step 5

Continue to run the knife around all four edges of the USB port until the glue is released. You may be able to gently wiggle the knife from side to side to help release the glue.

Continue to run the knife around all four edges of the USB port until the glue is released. You may be able to gently wiggle the knife from side to side to help release the glue.

Step 6

Use a spudger to push on the headphone jack and slide the USB port out of its housing.
If the USB port doesn’t come free, check to make sure all the glue holding the USB port in place has been released. Pulling on the USB port itself is not recommended as there is a fragile ribbon cable that can be ripped if the USB port suddenly comes free.

Use a spudger to push on the headphone jack and slide the USB port out of its housing.

If the USB port doesn’t come free, check to make sure all the glue holding the USB port in place has been released. Pulling on the USB port itself is not recommended as there is a fragile ribbon cable that can be ripped if the USB port suddenly comes free.

Step 7

After the USB port comes free, carefully slide it out of its housing. Don’t pull it out too far because there’s still a ribbon cable connecting it to the logic board.

After the USB port comes free, carefully slide it out of its housing. Don’t pull it out too far because there’s still a ribbon cable connecting it to the logic board.

Step 8

Continue to slide the iPod out of its casing by using a spudger to push on the logic board near the headphone jack.

Continue to slide the iPod out of its casing by using a spudger to push on the logic board near the headphone jack.

Step 9

Turn the iPod so that the click wheel is facing up. This will prevent the battery indicator from falling out.
If the battery indicator does fall out, don’t forget to replace it prior to reassembling the iPod. Getting the battery indicator back in place can be tricky. You’ll have to slide it in from the end of the iPod’s casing and get it to fall into its slot in the casing.
Slide the iPod out of its casing.

Turn the iPod so that the click wheel is facing up. This will prevent the battery indicator from falling out.

If the battery indicator does fall out, don’t forget to replace it prior to reassembling the iPod. Getting the battery indicator back in place can be tricky. You’ll have to slide it in from the end of the iPod’s casing and get it to fall into its slot in the casing.

Slide the iPod out of its casing.

Step 10

              USB Port

Use a spudger to flip up the black plastic tab holding the USB port ribbon in place. The black tab will rotate up 90 degrees, releasing the ribbon cable.

Use a spudger to flip up the black plastic tab holding the USB port ribbon in place. The black tab will rotate up 90 degrees, releasing the ribbon cable.

Step 11

Carefully peel the yellow USB ribbon up from the battery.

Carefully peel the yellow USB ribbon up from the battery.

Step 12

Slide the USB ribbon out of its connector.
Lift the USB port and detached ribbon cable out of the iPod.

Slide the USB ribbon out of its connector.

Lift the USB port and detached ribbon cable out of the iPod.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      4 other people completed this guide.

Author

                                      with 1 other contributor

                    iRobot

Member since: 09/24/2009

1 Reputation

                                      646 Guides authored                  



                       Badges:
                       36







                                                        +33 more badges

Introduction#

What you need#

Introduction

What you need