Difficulty

Moderate

Steps

7

Time Required

                          20 minutes

Sections

2

  • Rear Panel
  • 4 steps
  • Headphone Jack Bracket
  • 3 steps

Flags

0

  • BackiPod 4th Generation or Photo

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Rear Panel
  • Before opening your iPod, ensure that the hold switch is in the locked position. The orange bar should be visible, indicating hold is active.

Before opening your iPod, ensure that the hold switch is in the locked position. The orange bar should be visible, indicating hold is active.

1024

Step 2

  • Insert an opening pick as far as possible into the seam between the plastic front and the metal rear panel, on the right edge of the iPod.
  • You may need to rock the pick back and forth to slide it in farther.
  • Use the opening pick to pry up against the plastic front panel and release five retaining tabs (seen in the third photo).
  • Slide the pick along the edge of the iPod and continue prying to release the rest of the retaining tabs.
  • After all five tabs along the right side are free, the case should easily open.

Insert an opening pick as far as possible into the seam between the plastic front and the metal rear panel, on the right edge of the iPod.

You may need to rock the pick back and forth to slide it in farther.

Use the opening pick to pry up against the plastic front panel and release five retaining tabs (seen in the third photo).

Slide the pick along the edge of the iPod and continue prying to release the rest of the retaining tabs.

After all five tabs along the right side are free, the case should easily open.

Step 3

  • The iPod case is now open, but don’t separate the two halves just yet. There is still an orange ribbon cable connecting the headphone jack to the logic board.
  • Open the case like a book with the dock connector edge at the top, and lay the rear panel next to the front half of the iPod.

The iPod case is now open, but don’t separate the two halves just yet. There is still an orange ribbon cable connecting the headphone jack to the logic board.

Open the case like a book with the dock connector edge at the top, and lay the rear panel next to the front half of the iPod.

Step 4

  • Use a plastic tool or your fingernails to carefully disconnect the orange headphone jack cable. Be sure to pull straight up on the connector, not the cable itself.
  • This ribbon cable is very fragile. If you are replacing the battery, you can choose to skip this step and keep the headphone jack connected to the motherboard. Prop and tape the rear case against a box to keep it in place. Be very careful not to strain the fragile headphone jack cable as you work.

Use a plastic tool or your fingernails to carefully disconnect the orange headphone jack cable. Be sure to pull straight up on the connector, not the cable itself.

This ribbon cable is very fragile. If you are replacing the battery, you can choose to skip this step and keep the headphone jack connected to the motherboard. Prop and tape the rear case against a box to keep it in place. Be very careful not to strain the fragile headphone jack cable as you work.

Step 5

              Headphone Jack Bracket
  • Remove the 2 silver T6 Torx screws from the headphone jack.

Remove the 2 silver T6 Torx screws from the headphone jack.

Step 6

  • Remove the 3 silver Philips screws securing the headphone jack to the rear panel.

Remove the 3 silver Philips screws securing the headphone jack to the rear panel.

Step 7

  • Grasp the white headphone jack bracket and lift it out of the iPod.

Grasp the white headphone jack bracket and lift it out of the iPod.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      4 other people completed this guide.

Author

                                      with 3 other contributors 


                    iRobot

Member since: 09/24/2009

1 Reputation

                                      646 Guides authored                  



                       Badges:
                       36







                                                        +33 more badges

albidu-vacation - Mar 21, 2017

Reply

Acquistando il ricambio “headphone jack bracket” viene fornito anche il flat cable con connettore?

Purtroppo a me si è staccato il connettore dal flat cable e non viene fornito come ricambio, la speranza è che che comperando l’ “headphone jack bracket” venga fornito con flat e connettore.

Grazie a tutti!