Ipod 4Th Generation Or Photo Display Replacement Repair Guide

Featured

Featured Guide

Difficulty

Moderate

Steps

Time Required

                          5 - 25 minutes

Sections

Rear Panel
4 steps
Hard Drive
1 step
Hard Drive Cable
3 steps
Logic Board
5 steps
Display
1 step

Flags

Featured Guide

This guide has been found to be exceptionally cool by the iFixit staff.

BackiPod 4th Generation or Photo
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Rear Panel

Before opening your iPod, ensure that the hold switch is in the locked position. The orange bar should be visible, indicating hold is active.

Before opening your iPod, ensure that the hold switch is in the locked position. The orange bar should be visible, indicating hold is active.

1024

Step 2

Insert an opening pick as far as possible into the seam between the plastic front and the metal rear panel, on the right edge of the iPod.
You may need to rock the pick back and forth to slide it in farther.
Use the opening pick to pry up against the plastic front panel and release five retaining tabs (seen in the third photo).
Slide the pick along the edge of the iPod and continue prying to release the rest of the retaining tabs.
After all five tabs along the right side are free, the case should easily open.

Insert an opening pick as far as possible into the seam between the plastic front and the metal rear panel, on the right edge of the iPod.

You may need to rock the pick back and forth to slide it in farther.

Use the opening pick to pry up against the plastic front panel and release five retaining tabs (seen in the third photo).

Slide the pick along the edge of the iPod and continue prying to release the rest of the retaining tabs.

After all five tabs along the right side are free, the case should easily open.

Step 3

The iPod case is now open, but don’t separate the two halves just yet. There is still an orange ribbon cable connecting the headphone jack to the logic board.
Open the case like a book with the dock connector edge at the top, and lay the rear panel next to the front half of the iPod.

The iPod case is now open, but don’t separate the two halves just yet. There is still an orange ribbon cable connecting the headphone jack to the logic board.

Open the case like a book with the dock connector edge at the top, and lay the rear panel next to the front half of the iPod.

Step 4

Use a plastic tool or your fingernails to carefully disconnect the orange headphone jack cable. Be sure to pull straight up on the connector, not the cable itself.
This ribbon cable is very fragile. If you are replacing the battery, you can choose to skip this step and keep the headphone jack connected to the motherboard. Prop and tape the rear case against a box to keep it in place. Be very careful not to strain the fragile headphone jack cable as you work.

Use a plastic tool or your fingernails to carefully disconnect the orange headphone jack cable. Be sure to pull straight up on the connector, not the cable itself.

This ribbon cable is very fragile. If you are replacing the battery, you can choose to skip this step and keep the headphone jack connected to the motherboard. Prop and tape the rear case against a box to keep it in place. Be very careful not to strain the fragile headphone jack cable as you work.

Step 5

              Hard Drive

Grasp the hard drive with one hand and carefully disconnect the orange ribbon cable from the hard drive using your other hand.
If the cable doesn’t come free easily, it may be helpful to gently wiggle the cable from side to side.

Grasp the hard drive with one hand and carefully disconnect the orange ribbon cable from the hard drive using your other hand.

If the cable doesn’t come free easily, it may be helpful to gently wiggle the cable from side to side.

Step 6

              Hard Drive Cable

Peel up the black adhesive strip covering the hard drive ribbon cable.

Peel up the black adhesive strip covering the hard drive ribbon cable.

Step 7

Use the tip of your finger or a spudger to carefully flip up the black connector securing the hard drive cable to the logic board. Note that the black retaining clip flips 90 degrees toward vertical, in the direction of the cable.

Use the tip of your finger or a spudger to carefully flip up the black connector securing the hard drive cable to the logic board. Note that the black retaining clip flips 90 degrees toward vertical, in the direction of the cable.

Step 8

Pull the orange hard drive cable directly out of its connector.

Pull the orange hard drive cable directly out of its connector.

Step 9

              Logic Board

Carefully disconnect the white battery connector from the logic board. Be sure to pull only on the connector itself and not on the cables.

Carefully disconnect the white battery connector from the logic board. Be sure to pull only on the connector itself and not on the cables.

Step 10

Use a spudger to flip up the black retaining bars securing the display and click wheel connectors to the logic board.
If you have an iPod Photo, the display connector (to the right of the picture) is located more centrally on the logic board.

Use a spudger to flip up the black retaining bars securing the display and click wheel connectors to the logic board.

If you have an iPod Photo, the display connector (to the right of the picture) is located more centrally on the logic board.

Step 11

Remove the 6 black T6 Torx screws securing the logic board to the front panel.
If you have an iPod Photo, there will only be 5 screws, as there is no screw in the top right corner of the iPod.

Remove the 6 black T6 Torx screws securing the logic board to the front panel.

If you have an iPod Photo, there will only be 5 screws, as there is no screw in the top right corner of the iPod.

Step 12

Slide the orange click wheel ribbon cable out of its connector. You must unlock this connector before sliding the ribbon cable out. The locking mechanism is on the opposite side of where the cable is inserted - it swivels upwards 90 degrees. Use a plastic spudger to lift the locking mechanism.

Slide the orange click wheel ribbon cable out of its connector. You must unlock this connector before sliding the ribbon cable out. The locking mechanism is on the opposite side of where the cable is inserted - it swivels upwards 90 degrees. Use a plastic spudger to lift the locking mechanism.

Step 13

Carefully lift up the large end of the logic board and disconnect the display connector.
Lift the logic board out of the iPod.

Carefully lift up the large end of the logic board and disconnect the display connector.

Lift the logic board out of the iPod.

Step 14

              Display

Lift the display panel out of the iPod. There may be some mild adhesive connecting the display to the front panel.

Lift the display panel out of the iPod. There may be some mild adhesive connecting the display to the front panel.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      48 other people completed this guide.

Author

                                      with 5 other contributors

                    iRobot

Member since: 09/24/2009

1 Reputation

                                      646 Guides authored                  



                       Badges:
                       36







                                                        +33 more badges

Featured Guide#

Introduction#

What you need#

Featured Guide

Introduction

What you need