Difficulty
Moderate
Steps
36
Time Required
1 - 2 hours
Sections
6
- Pentalobe Screws
- 1 step
- Opening Procedure
- 10 steps
- Display Assembly
- 10 steps
- Lower Speaker
- 10 steps
- Taptic Engine Assembly
- 4 steps
- Taptic Engine
- 1 step
Flags
0
BackiPhone XS Max
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
This guide instructs you to fully remove the display assembly; this is intended to prevent accidental strain or damage to the display cables while you work. If you feel comfortable removing the Taptic Engine without endangering the display cables, you can skip the steps for disconnecting the display cables.
What you need
Step 1
Pentalobe Screws
- Before you begin, discharge your iPhone battery below 25%. A charged lithium-ion battery can catch fire and/or explode if accidentally punctured.
- Power off your iPhone before beginning disassembly.
- Remove the two 6.9 mm-long pentalobe screws at the bottom edge of the iPhone.
- Opening the iPhone’s display will compromise its waterproof seals. Have replacement seals ready before you proceed past this step, or take care to avoid liquid exposure if you reassemble your iPhone without replacing the seals.
Before you begin, discharge your iPhone battery below 25%. A charged lithium-ion battery can catch fire and/or explode if accidentally punctured.
Power off your iPhone before beginning disassembly.
Remove the two 6.9 mm-long pentalobe screws at the bottom edge of the iPhone.
Opening the iPhone’s display will compromise its waterproof seals. Have replacement seals ready before you proceed past this step, or take care to avoid liquid exposure if you reassemble your iPhone without replacing the seals.
1024
Step 2
Opening Procedure
- Heating the lower edge of the iPhone helps soften the adhesive securing the display, making it easier to open.
- Use a hairdryer or heat gun or prepare an iOpener and apply it to the lower edge of the iPhone for about a minute in order to soften up the adhesive underneath.
Heating the lower edge of the iPhone helps soften the adhesive securing the display, making it easier to open.
Use a hairdryer or heat gun or prepare an iOpener and apply it to the lower edge of the iPhone for about a minute in order to soften up the adhesive underneath.
Step 3
- The next two steps demonstrate the iSclack, a handy tool that we recommend for anyone doing frequent repairs. If you aren’t using the iSclack, skip down two steps for an alternate method.
- If the plastic depth gauge is attached at the center of the iSclack, remove it now—it’s not needed for larger iPhones like the XS Max.
- Position the suction cups near the bottom edge of the iPhone—one on the front, and one on the back.
- Press both suction cups firmly into place.
- If your display or back glass is badly cracked, covering it with a layer of clear packing tape may help the suction cups adhere. The iSclack also includes two pieces of tape for this purpose.
The next two steps demonstrate the iSclack, a handy tool that we recommend for anyone doing frequent repairs. If you aren’t using the iSclack, skip down two steps for an alternate method.
If the plastic depth gauge is attached at the center of the iSclack, remove it now—it’s not needed for larger iPhones like the XS Max.
Position the suction cups near the bottom edge of the iPhone—one on the front, and one on the back.
Press both suction cups firmly into place.
If your display or back glass is badly cracked, covering it with a layer of clear packing tape may help the suction cups adhere. The iSclack also includes two pieces of tape for this purpose.
Step 4
- Hold onto your iPhone securely and close the handle of the iSclack to slightly separate the screen from the rear case of the phone.
- Don’t try to completely separate the screen; a small opening along the bottom edge is all you need.
- Insert an opening pick into the gap under the display on the lower edge of the iPhone.
- Skip the next two steps.
Hold onto your iPhone securely and close the handle of the iSclack to slightly separate the screen from the rear case of the phone.
Don’t try to completely separate the screen; a small opening along the bottom edge is all you need.
Insert an opening pick into the gap under the display on the lower edge of the iPhone.
Skip the next two steps.
Step 5
- If you’re using a single suction handle, apply it to the bottom edge of the phone, while avoiding the curved portion of the glass.
- If your display is badly cracked, covering it with a layer of clear packing tape may allow the suction cup to adhere. Alternatively, very strong tape may be used instead of the suction cup. If all else fails, you can superglue the suction cup to the broken screen.
If you’re using a single suction handle, apply it to the bottom edge of the phone, while avoiding the curved portion of the glass.
If your display is badly cracked, covering it with a layer of clear packing tape may allow the suction cup to adhere. Alternatively, very strong tape may be used instead of the suction cup. If all else fails, you can superglue the suction cup to the broken screen.
Step 6
- Pull up on the suction cup with firm, constant pressure to create a slight gap between the front panel and rear case.
- Insert an opening pick into the gap.
- The watertight adhesive holding the display in place is very strong; creating this initial gap takes a significant amount of force. If you’re having a hard time opening a gap, apply more heat, and gently rock the screen up and down to weaken the adhesive until you create enough of a gap to insert your tool.
Pull up on the suction cup with firm, constant pressure to create a slight gap between the front panel and rear case.
Insert an opening pick into the gap.
The watertight adhesive holding the display in place is very strong; creating this initial gap takes a significant amount of force. If you’re having a hard time opening a gap, apply more heat, and gently rock the screen up and down to weaken the adhesive until you create enough of a gap to insert your tool.
Step 7
- Slide the opening pick around the lower left corner and up the left edge of the iPhone, slicing through the adhesive holding the display in place.
- Don’t insert the opening pick too far into the iPhone, or you may cause damage to internal components.
Slide the opening pick around the lower left corner and up the left edge of the iPhone, slicing through the adhesive holding the display in place.
Don’t insert the opening pick too far into the iPhone, or you may cause damage to internal components.
Step 8
- Re-insert your pick at the bottom edge of the iPhone, and slide it up the right side to continue separating the adhesive.
- Don’t insert the pick very far, or you may damage the display cables along this side of the iPhone. Insert it only a few millimeters, or about the width of the display bezel.
Re-insert your pick at the bottom edge of the iPhone, and slide it up the right side to continue separating the adhesive.
Don’t insert the pick very far, or you may damage the display cables along this side of the iPhone. Insert it only a few millimeters, or about the width of the display bezel.
Step 9
- The top edge of the display is secured with both glue and clips.
- Slide the opening pick around the top corner of the display, while gently pulling or wiggling the display down in the direction of the Lightning port.
- The clips will break if you use too much force. Work carefully and be patient.
- Again, don’t insert the pick more than a few millimeters—about the width of the display bezel—or you may damage the front panel sensor array.
- Slide the pick to the opposite corner and cut any remaining adhesive securing the display.
The top edge of the display is secured with both glue and clips.
Slide the opening pick around the top corner of the display, while gently pulling or wiggling the display down in the direction of the Lightning port.
The clips will break if you use too much force. Work carefully and be patient.
Again, don’t insert the pick more than a few millimeters—about the width of the display bezel—or you may damage the front panel sensor array.
Slide the pick to the opposite corner and cut any remaining adhesive securing the display.
Step 10
- Pull on the small nub on the suction cup to remove it from the front panel.
- If you used an iSclack and it’s still affixed to the iPhone, remove it now.
Pull on the small nub on the suction cup to remove it from the front panel.
If you used an iSclack and it’s still affixed to the iPhone, remove it now.
Step 11
- Open the iPhone by swinging the display up from the left side, like the back cover of a book.
- Don’t try to fully separate the display yet, as several fragile ribbon cables still connect it to the iPhone’s logic board.
- Lean the display against something to keep it propped up while you’re working on the phone.
- During reassembly, lay the display in position, align the clips along the top edge, and carefully press the top edge into place before snapping the rest of the display down. If it doesn’t click easily into place, check the condition of the clips around the perimeter of the display and make sure they aren’t bent.
Open the iPhone by swinging the display up from the left side, like the back cover of a book.
Don’t try to fully separate the display yet, as several fragile ribbon cables still connect it to the iPhone’s logic board.
Lean the display against something to keep it propped up while you’re working on the phone.
During reassembly, lay the display in position, align the clips along the top edge, and carefully press the top edge into place before snapping the rest of the display down. If it doesn’t click easily into place, check the condition of the clips around the perimeter of the display and make sure they aren’t bent.
Step 12
Display Assembly
- Remove four Y000 screws securing the logic board cover bracket, of the following lengths:
- Two 1.1 mm screws
- One 1.5 mm screw
- One 3.7 mm screw
- Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from to avoid damaging your iPhone.
Remove four Y000 screws securing the logic board cover bracket, of the following lengths:
Two 1.1 mm screws
One 1.5 mm screw
One 3.7 mm screw
Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from to avoid damaging your iPhone.
Step 13
- Remove the bracket.
- The bracket may be lightly adhered in place. Lift gently but firmly to separate it.
- During reassembly, this is a good point to power on your iPhone and test all functions before you seal the display in place. Be sure to power your iPhone back down completely before you continue working.
Remove the bracket.
The bracket may be lightly adhered in place. Lift gently but firmly to separate it.
During reassembly, this is a good point to power on your iPhone and test all functions before you seal the display in place. Be sure to power your iPhone back down completely before you continue working.
Step 14
- Use a spudger or a clean fingernail to pry the battery connector up from its socket on the logic board.
- Try not to damage the black silicone seal surrounding this and other board connections. These seals provide extra protection against water and dust intrusion.
- Bend the connector slightly away from the logic board to prevent it from accidentally making contact with the socket and providing power to the phone during your repair.
Use a spudger or a clean fingernail to pry the battery connector up from its socket on the logic board.
Try not to damage the black silicone seal surrounding this and other board connections. These seals provide extra protection against water and dust intrusion.
Bend the connector slightly away from the logic board to prevent it from accidentally making contact with the socket and providing power to the phone during your repair.
Step 15
- Remove the three Y000 screws securing the display connector bracket:
- Two 1.5 mm screws
- One 1.1 mm screw
Remove the three Y000 screws securing the display connector bracket:
Two 1.5 mm screws
One 1.1 mm screw
Step 16
- Remove the bracket.
Step 17
- Use the point of a spudger or a fingernail to disconnect the front panel sensor assembly connector.
Use the point of a spudger or a fingernail to disconnect the front panel sensor assembly connector.
Step 18
- Use a spudger or a fingernail to disconnect the OLED panel cable connector.
- To re-attach press connectors like this one, carefully align and press down on one side until it clicks into place, then repeat on the other side. Do not press down on the middle. If the connector is misaligned, the pins can bend, causing permanent damage.
Use a spudger or a fingernail to disconnect the OLED panel cable connector.
To re-attach press connectors like this one, carefully align and press down on one side until it clicks into place, then repeat on the other side. Do not press down on the middle. If the connector is misaligned, the pins can bend, causing permanent damage.
Step 19
- Use a spudger or fingernail to pry the digitizer cable connector up from its socket.
- If any part of your screen doesn’t respond to touch after your repair, disconnect the battery and then re-seat this connector, making sure it clicks fully into place and that there’s no dust or other obstruction in the socket.
Use a spudger or fingernail to pry the digitizer cable connector up from its socket.
If any part of your screen doesn’t respond to touch after your repair, disconnect the battery and then re-seat this connector, making sure it clicks fully into place and that there’s no dust or other obstruction in the socket.
Step 20
- The front panel sensor assembly flex cable is lightly adhered in place.
- Carefully lift the cable until the adhesive separates.
The front panel sensor assembly flex cable is lightly adhered in place.
Carefully lift the cable until the adhesive separates.
Step 21
- Remove the display assembly.
- During reassembly, pause here if you wish to replace the waterproof adhesive around the edges of the display.
Remove the display assembly.
During reassembly, pause here if you wish to replace the waterproof adhesive around the edges of the display.
Step 22
Lower Speaker
- Remove the five 1.4 mm tri-point Y000 screws securing the bracket below the Taptic Engine and main speaker.
Remove the five 1.4 mm tri-point Y000 screws securing the bracket below the Taptic Engine and main speaker.
Step 23
- The bracket is lightly adhered in place.
- Gently lift to unstick and remove the bracket, being careful not to bend it.
- If necessary, apply a little heat with a hair dryer or heat gun to soften the adhesive. (Putting an iOpener on the bracket is not recommended, as this may bend the spring contacts along the top.)
The bracket is lightly adhered in place.
Gently lift to unstick and remove the bracket, being careful not to bend it.
If necessary, apply a little heat with a hair dryer or heat gun to soften the adhesive. (Putting an iOpener on the bracket is not recommended, as this may bend the spring contacts along the top.)
Step 24
- Remove the 1.3 mm tri-point Y000 screw securing the speaker connector cover.
Remove the 1.3 mm tri-point Y000 screw securing the speaker connector cover.
Step 25
- Push the speaker connector cover towards the battery, and then lift to unclip and remove it.
- Be very careful not to poke or puncture the battery with your tools.
Push the speaker connector cover towards the battery, and then lift to unclip and remove it.
Be very careful not to poke or puncture the battery with your tools.
Step 26
- Use the tip of a spudger to pry up and disconnect the speaker connector.
Use the tip of a spudger to pry up and disconnect the speaker connector.
Step 27
- Remove the three screws securing the speaker:
- One 2.7 mm Phillips screw
- One 2.9 mm standoff screw
- One 3.1 mm standoff screw
- Standoff screws are best removed using an iPhone Standoff bit and driver handle.
- In a pinch, a small flathead screwdriver will do the job—but use extra caution to ensure it doesn’t slip and damage surrounding components.
Remove the three screws securing the speaker:
One 2.7 mm Phillips screw
One 2.9 mm standoff screw
One 3.1 mm standoff screw
Standoff screws are best removed using an iPhone Standoff bit and driver handle.
In a pinch, a small flathead screwdriver will do the job—but use extra caution to ensure it doesn’t slip and damage surrounding components.
Step 28
- When prying up the speaker, take care not to damage the speaker flex cable you just disconnected. If necessary, bend the cable toward the battery so the speaker has room to come out.
- Insert a spudger under the top edge of the speaker, near the edge of the iPhone’s case.
- Gently pry up and lift the top edge of the speaker slightly.
- When reinstalling the speaker, check the position of the flex cable and make sure it doesn’t get trapped underneath the speaker.
When prying up the speaker, take care not to damage the speaker flex cable you just disconnected. If necessary, bend the cable toward the battery so the speaker has room to come out.
Insert a spudger under the top edge of the speaker, near the edge of the iPhone’s case.
Gently pry up and lift the top edge of the speaker slightly.
When reinstalling the speaker, check the position of the flex cable and make sure it doesn’t get trapped underneath the speaker.
Step 29
- While prying up the speaker, use tweezers to peel away the plastic bumper strip from the top edge of the speaker.
- If necessary, apply a little heat to soften the adhesive and make the bumper strip easier to separate.
While prying up the speaker, use tweezers to peel away the plastic bumper strip from the top edge of the speaker.
If necessary, apply a little heat to soften the adhesive and make the bumper strip easier to separate.
Step 30
- Hold the speaker by its side edges and rock it side-to-side, separating the adhesive securing it to the bottom edge of the iPhone.
- Pull the speaker away from the bottom edge of the iPhone until the adhesive gasket separates.
Hold the speaker by its side edges and rock it side-to-side, separating the adhesive securing it to the bottom edge of the iPhone.
Pull the speaker away from the bottom edge of the iPhone until the adhesive gasket separates.
Step 31
- Remove the speaker.
- The speaker’s adhesive gasket is not reusable. Peel away any remaining adhesive residue with tweezers.
- To help protect against water and dust intrusion, replace the adhesive gasket during reassembly. Prep the area by cleaning it with a bit of isopropyl alcohol and a lint-free cloth or coffee filter so that the gasket adheres properly. Install a new gasket onto the speaker, and then install the speaker.
Remove the speaker.
The speaker’s adhesive gasket is not reusable. Peel away any remaining adhesive residue with tweezers.
To help protect against water and dust intrusion, replace the adhesive gasket during reassembly. Prep the area by cleaning it with a bit of isopropyl alcohol and a lint-free cloth or coffee filter so that the gasket adheres properly. Install a new gasket onto the speaker, and then install the speaker.
Step 32
Taptic Engine Assembly
- Use a spudger to disconnect the Taptic Engine flex cable by prying it straight up from its socket.
Use a spudger to disconnect the Taptic Engine flex cable by prying it straight up from its socket.
Step 33
- Remove the two 1.9 mm Phillips screws securing the Taptic Engine.
Remove the two 1.9 mm Phillips screws securing the Taptic Engine.
Step 34
- Grasp the plastic bumper strip and carefully lift it over the speaker connector.
Grasp the plastic bumper strip and carefully lift it over the speaker connector.
Step 35
- Remove the Taptic Engine assembly.
- The contact clip on the left side of the Taptic Engine may fall off. Be sure it’s installed correctly as shown before reinstalling the Taptic Engine in the iPhone.
Remove the Taptic Engine assembly.
The contact clip on the left side of the Taptic Engine may fall off. Be sure it’s installed correctly as shown before reinstalling the Taptic Engine in the iPhone.
Step 36
Taptic Engine
- Peel up and remove the plastic bumper strip from the Taptic Engine.
Peel up and remove the plastic bumper strip from the Taptic Engine.
Compare your new replacement part to the original part—you may need to transfer remaining components or remove adhesive backings from the new part before installing.
To reassemble your device, follow the above steps in reverse order.
Take your e-waste to an R2 or e-Stewards certified recycler.
Repair didn’t go as planned? Check out our Answers community for troubleshooting help.
Cancel: I did not complete this guide.
14 other people completed this guide.
Author
Jeff Suovanen
Member since: 08/06/2013
401,020 Reputation
261 Guides authored
Badges:
48
+45 more badges
Team
iFixit
Member of iFixit
Community
141 Members
15,769 Guides authored
