Featured

Featured Guide

Difficulty

Moderate

Steps

26

Time Required

                          30 minutes - 1 hour

Sections

6

  • Pentalobe Screws
  • 1 step
  • Taping Over The Display
  • 1 step
  • iPhone 7 Opening Procedure
  • 10 steps
  • Battery Disconnection
  • 3 steps
  • Display Assembly
  • 4 steps
  • Home/Touch ID Sensor
  • 7 steps

Flags

1

This guide has been found to be exceptionally cool by the iFixit staff.

  • BackiPhone 7

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

All you need to do is remove the old screen and transfer the home button to the new screen, in order for Touch ID to function.

What you need

Video Overview

Step 1

              Pentalobe Screws
  • Before you begin, discharge your iPhone battery below 25%. A charged lithium-ion battery can catch fire and/or explode if accidentally punctured.
  • Power off your iPhone before beginning disassembly.
  • Remove the two 3.4 mm pentalobe screws on the bottom edge of the iPhone.
  • Opening the iPhone’s display will compromise its waterproof seals. Have replacement seals ready before you proceed past this step, or take care to avoid liquid exposure if you reassemble your iPhone without replacing the seals.

Before you begin, discharge your iPhone battery below 25%. A charged lithium-ion battery can catch fire and/or explode if accidentally punctured.

Power off your iPhone before beginning disassembly.

Remove the two 3.4 mm pentalobe screws on the bottom edge of the iPhone.

Opening the iPhone’s display will compromise its waterproof seals. Have replacement seals ready before you proceed past this step, or take care to avoid liquid exposure if you reassemble your iPhone without replacing the seals.

1024

Step 2

              Tape over the display
  • If your display glass is cracked, keep further breakage contained and prevent bodily harm during your repair by taping over the glass.
  • Lay overlapping strips of clear packing tape over the iPhone’s display until the whole face is covered.
  • This will keep glass shards contained and provide structural integrity when prying and lifting the display.
  • Wear safety glasses to protect your eyes from any glass shaken free during the repair.
  • If the broken glass makes it difficult to get a suction cup to stick in the next few steps, try folding a strong piece of tape (such as duct tape) into a handle and lifting the display with that instead.

If your display glass is cracked, keep further breakage contained and prevent bodily harm during your repair by taping over the glass.

Lay overlapping strips of clear packing tape over the iPhone’s display until the whole face is covered.

This will keep glass shards contained and provide structural integrity when prying and lifting the display.

Wear safety glasses to protect your eyes from any glass shaken free during the repair.

If the broken glass makes it difficult to get a suction cup to stick in the next few steps, try folding a strong piece of tape (such as duct tape) into a handle and lifting the display with that instead.

Step 3

              iPhone 7 Opening Procedure
  • Heating the lower edge of the iPhone will help soften the adhesive securing the display, making it easier to open.
  • Use a hairdryer or prepare an iOpener and apply it to the lower edge of the iPhone for about a minute in order to soften up the adhesive underneath.

Heating the lower edge of the iPhone will help soften the adhesive securing the display, making it easier to open.

Use a hairdryer or prepare an iOpener and apply it to the lower edge of the iPhone for about a minute in order to soften up the adhesive underneath.

Step 4

  • Attach a suction cup to the lower half of the display assembly, just above the home button.
  • Be sure the suction cup does not overlap with the home button, as this will prevent a seal from forming between the suction cup and front glass.
  • If your display is badly cracked, covering it with a layer of clear packing tape may allow the suction cup to adhere. Alternatively, very strong tape may be used instead of the suction cup. If all else fails, you can superglue the suction cup to the broken screen.

Attach a suction cup to the lower half of the display assembly, just above the home button.

Be sure the suction cup does not overlap with the home button, as this will prevent a seal from forming between the suction cup and front glass.

If your display is badly cracked, covering it with a layer of clear packing tape may allow the suction cup to adhere. Alternatively, very strong tape may be used instead of the suction cup. If all else fails, you can superglue the suction cup to the broken screen.

Step 5

  • Pull up on the suction cup to create a small gap between the display assembly and the rear case.
  • Insert the flat end of a spudger into the gap.
  • The watertight adhesive holding the display in place is very strong, and creating this initial gap takes a significant amount of force. If you’re having a hard time opening a gap, rock the screen up and down to weaken the adhesive until you can fit a spudger inside.

Pull up on the suction cup to create a small gap between the display assembly and the rear case.

Insert the flat end of a spudger into the gap.

The watertight adhesive holding the display in place is very strong, and creating this initial gap takes a significant amount of force. If you’re having a hard time opening a gap, rock the screen up and down to weaken the adhesive until you can fit a spudger inside.

Step 6

  • Slide the spudger to the left along the lower edge of the iPhone.
  • Twist the spudger to widen the gap between the display and rear case.

Slide the spudger to the left along the lower edge of the iPhone.

Twist the spudger to widen the gap between the display and rear case.

Step 7

  • Slide the spudger up the left side of the iPhone, starting at the lower edge and moving towards the volume control buttons and silent switch.
  • Do not pry along the top edge of the phone, you risk damaging the plastic clips securing the display.

Slide the spudger up the left side of the iPhone, starting at the lower edge and moving towards the volume control buttons and silent switch.

Do not pry along the top edge of the phone, you risk damaging the plastic clips securing the display.

Step 8

  • Insert the flat edge of a spudger into the bottom right corner of the device.
  • Twist the spudger to widen the gap between the display assembly and the rear case.
  • Slide the flat end of the spudger up the right side of the phone to break up the adhesive holding the display in place.
  • Do not insert the spudger further than the adhesive to avoid damaging delicate ribbon cables along the right edge.

Insert the flat edge of a spudger into the bottom right corner of the device.

Twist the spudger to widen the gap between the display assembly and the rear case.

Slide the flat end of the spudger up the right side of the phone to break up the adhesive holding the display in place.

Do not insert the spudger further than the adhesive to avoid damaging delicate ribbon cables along the right edge.

Step 9

  • Pull up on the suction cup to lift up the display and open the iPhone.
  • Do not raise the display more than 10º as there are ribbon cables along the right edge of the device connecting the display to the logic board.

Pull up on the suction cup to lift up the display and open the iPhone.

Do not raise the display more than 10º as there are ribbon cables along the right edge of the device connecting the display to the logic board.

Step 10

  • Pull up on the small nub on the suction cup to remove it from the front panel.

Pull up on the small nub on the suction cup to remove it from the front panel.

Step 11

  • Slide an opening pick along the top edge of the iPhone, between the rear case and front panel, to break up the remaining adhesive holding the screen in place.
  • Be careful not to damage the plastic clips on the top edge of the phone.

Slide an opening pick along the top edge of the iPhone, between the rear case and front panel, to break up the remaining adhesive holding the screen in place.

Be careful not to damage the plastic clips on the top edge of the phone.

Step 12

  • Pull the display assembly slightly away from the top edge of the phone to disengage the clips holding it to the rear case.
  • Open the iPhone by swinging the display up from the left side, like the back cover of a book.
  • Don’t try to fully separate the display yet, as several fragile ribbon cables still connect it to the iPhone’s logic board.

Pull the display assembly slightly away from the top edge of the phone to disengage the clips holding it to the rear case.

Open the iPhone by swinging the display up from the left side, like the back cover of a book.

Don’t try to fully separate the display yet, as several fragile ribbon cables still connect it to the iPhone’s logic board.

Step 13

              Battery Disconnection
  • Remove four tri-point Y000 screws securing the lower connector bracket, of the following lengths:
  • Three 1.2 mm screws
  • One 2.4 mm screw
  • Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from to avoid damaging your iPhone.

Remove four tri-point Y000 screws securing the lower connector bracket, of the following lengths:

Three 1.2 mm screws

One 2.4 mm screw

Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from to avoid damaging your iPhone.

Step 14

  • Remove the lower connector bracket.

Remove the lower connector bracket.

Step 15

  • Use the point of a spudger to lift the battery connector out of its socket on the logic board.
  • Bend the connector cable up slightly to prevent it from making contact with the socket and providing power to the phone.

Use the point of a spudger to lift the battery connector out of its socket on the logic board.

Bend the connector cable up slightly to prevent it from making contact with the socket and providing power to the phone.

Step 16

              Display Assembly
  • Make sure the battery is disconnected before you disconnect or reconnect the cables in this step.
  • Use a spudger or a fingernail to disconnect the two lower display connectors by prying them straight up from their sockets on the logic board.
  • To reconnect these cables, press down on one end until it clicks into place, then repeat on the opposite end. Do not press down on the middle. If the connector is even slightly misaligned, the connector can bend, causing permanent damage.
  • If you have a blank screen, white lines on the display, or partial or complete lack of touch response after reassembling your phone, try disconnecting and carefully reconnecting both of these cables and make sure they are fully seated.

Make sure the battery is disconnected before you disconnect or reconnect the cables in this step.

Use a spudger or a fingernail to disconnect the two lower display connectors by prying them straight up from their sockets on the logic board.

To reconnect these cables, press down on one end until it clicks into place, then repeat on the opposite end. Do not press down on the middle. If the connector is even slightly misaligned, the connector can bend, causing permanent damage.

If you have a blank screen, white lines on the display, or partial or complete lack of touch response after reassembling your phone, try disconnecting and carefully reconnecting both of these cables and make sure they are fully seated.

Step 17

  • Remove the two 1.3 mm Phillips #000 screws securing the bracket over the front panel sensor assembly connector.
  • Some phones could be Y000. Apple started using Y000 for these at some point in the middle of the product’s lifecycle.

Remove the two 1.3 mm Phillips #000 screws securing the bracket over the front panel sensor assembly connector.

Some phones could be Y000. Apple started using Y000 for these at some point in the middle of the product’s lifecycle.

Step 18

  • Disconnect the front panel sensor assembly connector from its socket on the logic board.
  • This press connector should also be reconnected one end at a time to minimize the risk of bending.

Disconnect the front panel sensor assembly connector from its socket on the logic board.

This press connector should also be reconnected one end at a time to minimize the risk of bending.

Step 19

  • Remove the display assembly.
  • During reassembly, pause here if you wish to replace the adhesive around the edges of the display.

Remove the display assembly.

During reassembly, pause here if you wish to replace the adhesive around the edges of the display.

Step 20

              Home/Touch ID Sensor
  • Remove the four Y000 screws securing the bracket over the home/Touch ID sensor:
  • One 1.1 mm screw
  • Three 1.3 mm screws
  • During reassembly, be careful not to overtighten these screws, or your home button may not work.

Remove the four Y000 screws securing the bracket over the home/Touch ID sensor:

One 1.1 mm screw

Three 1.3 mm screws

During reassembly, be careful not to overtighten these screws, or your home button may not work.

Step 21

  • Remove the bracket that secures the home/Touch ID sensor.

Remove the bracket that secures the home/Touch ID sensor.

Step 22

  • Pry under the left edge of the home button cable connector to disconnect it from its socket.
  • If the entire connector begins to flip up without separating, press down on the cable at the top edge of the connector with the flat of your spudger, while simultaneously prying up the left edge of the connector. Be very careful not to damage the cable or connector, or you will permanently disable the sensor.

Pry under the left edge of the home button cable connector to disconnect it from its socket.

If the entire connector begins to flip up without separating, press down on the cable at the top edge of the connector with the flat of your spudger, while simultaneously prying up the left edge of the connector. Be very careful not to damage the cable or connector, or you will permanently disable the sensor.

Step 23

  • Carefully pry up the underlying connector and move it out of the way of the home/Touch ID cable.
  • It’s very easy to damage your iPhone during this step. Work slowly and take care where you pry with your tool. If you damage the Touch ID hardware, it can only be replaced by Apple.
  • If the connector doesn’t pry up easily, use a hair dryer or iOpener to heat and soften the adhesive securing the connector, and then try again.
  • Don’t try to detach the connector completely—simply flip it up slightly so that the underlying home/Touch ID sensor cable can be removed.

Carefully pry up the underlying connector and move it out of the way of the home/Touch ID cable.

It’s very easy to damage your iPhone during this step. Work slowly and take care where you pry with your tool. If you damage the Touch ID hardware, it can only be replaced by Apple.

If the connector doesn’t pry up easily, use a hair dryer or iOpener to heat and soften the adhesive securing the connector, and then try again.

Don’t try to detach the connector completely—simply flip it up slightly so that the underlying home/Touch ID sensor cable can be removed.

Step 24

  • Heating the area around the home/Touch ID sensor will help soften the adhesive holding its delicate cable in place, making it easier to remove safely.
  • Flip the display assembly over. Use a hairdryer or prepare an iOpener and apply it to the lower edge of the display for about 90 seconds in order to soften up the adhesive underneath.

Heating the area around the home/Touch ID sensor will help soften the adhesive holding its delicate cable in place, making it easier to remove safely.

Flip the display assembly over. Use a hairdryer or prepare an iOpener and apply it to the lower edge of the display for about 90 seconds in order to soften up the adhesive underneath.

Step 25

  • Use an opening pick to gently separate the adhesive holding the home/Touch ID sensor cable to the back side of the display panel.

Use an opening pick to gently separate the adhesive holding the home/Touch ID sensor cable to the back side of the display panel.

Step 26

  • Remove the home/Touch ID sensor assembly by lifting it through the front side of the display.
  • To reinstall, first feed the cable through the hole in the front of the display.
  • Your replacement part may come with an extra Y000 screw already installed right of the Home Button. Remove the unnecessary screw so that you can reinstall the home button bracket.
  • Follow this guide to install replacement display adhesive on your screen.

Remove the home/Touch ID sensor assembly by lifting it through the front side of the display.

To reinstall, first feed the cable through the hole in the front of the display.

Your replacement part may come with an extra Y000 screw already installed right of the Home Button. Remove the unnecessary screw so that you can reinstall the home button bracket.

Follow this guide to install replacement display adhesive on your screen.

To reassemble your device, follow these instructions in reverse order. Don’t forget to reapply the display adhesive before reinstalling the display.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our iPhone 7 Answers community for troubleshooting help.

Cancel: I did not complete this guide.

                                                                                      888 other people completed this guide.

Author

                                      with 10 other contributors 


                    Evan Noronha

Member since: 02/05/2015

218,062 Reputation

                                      177 Guides authored                  



                       Badges:
                       49







                                                        +46 more badges

Joseph - Oct 13, 2016

Reply

When putting the screen back on will the device loose it’s water-resistant properties?

Draydan - Oct 27, 2016

Wondering this too.

Jojo - Nov 7, 2016

It will for sure lose it’s water-resistant properties. So, please replace the water-resistant adhesive before assembly.

jaicdc - Nov 5, 2018

Yes, but you can buy a new replacement seal for a few bucks. However, it is extremely thin and very sticky so its almost impossible to do it right the first time (imagine placing a needle thin sized rubber band covered in glue around the tiny ledge you phone screen sits on). I would suggest you buy two because it is likely you’ll need a second shot at it…because if any part gets misplaced and sticks to the wrong spot, it will not come off, and that “sticky rubber band” turns into this horrible stringy tar/chewing gum ring that is impossible to manipulate…fair warning… it will most likely be pretty water resistant even if you don’t add a new seal to it… its not a waterproof phone in the first place :)

Alec - Nov 7, 2016

Reply

Yes it will lose the water-resistant abilities. It is very hard to seal it back to it’s original state.