Iphone 6S Plus Volume Control Cable Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          40 minutes - 2 hours

Sections

Pentalobe Screws
1 step
Opening Procedure
11 steps
Battery Connector
4 steps
Display Assembly
6 steps
Battery
4 steps
Volume Control Cable
9 steps

Flags

BackiPhone 6s Plus
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

You can also use this guide to replace the audio control cable bracket.

What you need

Step 1

              Pentalobe Screws

Before disassembling your iPhone, discharge the battery below 25%. A charged lithium-ion battery can catch fire and/or explode if accidentally punctured.
Power off your iPhone before beginning disassembly.
Remove the two 3.4 mm Pentalobe screws on either side of the Lightning port.

Before disassembling your iPhone, discharge the battery below 25%. A charged lithium-ion battery can catch fire and/or explode if accidentally punctured.

Power off your iPhone before beginning disassembly.

Remove the two 3.4 mm Pentalobe screws on either side of the Lightning port.

1024

Step 2

              Opening Procedure

Optionally, apply mild heat to the lower edge of the iPhone using an iOpener or hair dryer for about a minute.
Heat softens the adhesive securing the display, making it easier to open.

Optionally, apply mild heat to the lower edge of the iPhone using an iOpener or hair dryer for about a minute.

Heat softens the adhesive securing the display, making it easier to open.

Step 3

Opening the display on the 6s Plus separates a thin strip of adhesive around the perimeter of the display. If you prefer to replace the adhesive, have a set of new adhesive strips ready before you continue. It’s possible to complete the repair without replacing the adhesive, and you probably won’t notice any difference in functionality.
Apply a suction cup to the lower left corner of the display assembly.
If your display is badly cracked, covering it with a layer of clear packing tape may allow the suction cup to adhere. Alternatively, very strong tape may be used instead of the suction cup. If all else fails, you can superglue the suction cup to the broken screen.

Opening the display on the 6s Plus separates a thin strip of adhesive around the perimeter of the display. If you prefer to replace the adhesive, have a set of new adhesive strips ready before you continue. It’s possible to complete the repair without replacing the adhesive, and you probably won’t notice any difference in functionality.

Apply a suction cup to the lower left corner of the display assembly.

If your display is badly cracked, covering it with a layer of clear packing tape may allow the suction cup to adhere. Alternatively, very strong tape may be used instead of the suction cup. If all else fails, you can superglue the suction cup to the broken screen.

Step 4

Pull up on the suction cup with firm, constant pressure to create a slight gap between the front panel and rear case.
Pulling too hard may damage the display assembly. Apply just enough pressure to create a small gap between the display assembly and the rear case.

Pull up on the suction cup with firm, constant pressure to create a slight gap between the front panel and rear case.

Pulling too hard may damage the display assembly. Apply just enough pressure to create a small gap between the display assembly and the rear case.

Step 5

The safest place to pry from is the notch in the front panel above the headphone jack.
While still maintaining pressure on the suction cup, insert the flat tip of a spudger into the gap, directly above the headphone jack.

The safest place to pry from is the notch in the front panel above the headphone jack.

While still maintaining pressure on the suction cup, insert the flat tip of a spudger into the gap, directly above the headphone jack.

Step 6

Twist the spudger to widen the gap between the front panel and the rear case.

Twist the spudger to widen the gap between the front panel and the rear case.

Step 7

While firmly pulling up on the suction cup, slide the edge of the spudger under the bottom left corner of the display.

While firmly pulling up on the suction cup, slide the edge of the spudger under the bottom left corner of the display.

Step 8

Slide the tip of the spudger up the left side of the phone, between the front panel and the rear case.

Slide the tip of the spudger up the left side of the phone, between the front panel and the rear case.

Step 9

Insert the flat tip of the spudger under the right edge of the display.
Slide the spudger up the right side.

Insert the flat tip of the spudger under the right edge of the display.

Slide the spudger up the right side.

Step 10

Use a plastic opening tool to hold down the rear case while pulling up the suction cup to open the phone.
Do not remove the display completely, or you will damage the data cables connecting the display near the top edge of the iPhone.

Use a plastic opening tool to hold down the rear case while pulling up the suction cup to open the phone.

Do not remove the display completely, or you will damage the data cables connecting the display near the top edge of the iPhone.

Step 11

Pull up on the small nub on the suction cup to remove it from the display.

Pull up on the small nub on the suction cup to remove it from the display.

Step 12

Gently grasp the display assembly and lift it up to open the phone, using the clips at the top of the front panel as a hinge.
Open the display to about a 90º angle, and lean it against something to keep it propped up while you’re working on the phone.
Don’t open the display more than 90º—it is still connected to the top of the phone by the display, digitizer, and front camera cables which can tear easily.
Add a rubber band to keep the display securely in place while you work. This prevents undue strain on the display cables.
In a pinch, you can use an unopened canned beverage to support the display.

Gently grasp the display assembly and lift it up to open the phone, using the clips at the top of the front panel as a hinge.

Open the display to about a 90º angle, and lean it against something to keep it propped up while you’re working on the phone.

Don’t open the display more than 90º—it is still connected to the top of the phone by the display, digitizer, and front camera cables which can tear easily.

Add a rubber band to keep the display securely in place while you work. This prevents undue strain on the display cables.

In a pinch, you can use an unopened canned beverage to support the display.

Step 13

              Battery Connector

Remove two Phillips screws securing the battery connector bracket to the logic board, of the following lengths:
One 2.9 mm screw
One 2.3 mm screw
Throughout this guide, keep careful track of your screws so that each one goes back where it came from during reassembly. Installing a screw in the wrong place can cause permanent damage.

Remove two Phillips screws securing the battery connector bracket to the logic board, of the following lengths:

One 2.9 mm screw

One 2.3 mm screw

Throughout this guide, keep careful track of your screws so that each one goes back where it came from during reassembly. Installing a screw in the wrong place can cause permanent damage.

Step 14

Remove the battery connector bracket.

Remove the battery connector bracket.

Step 15

Use a spudger or a clean fingernail to disconnect the battery connector by prying it straight up off the logic board.

Use a spudger or a clean fingernail to disconnect the battery connector by prying it straight up off the logic board.

Step 16

Bend the connector back to ensure it doesn’t make contact and power the iPhone on while you’re working on it.

Bend the connector back to ensure it doesn’t make contact and power the iPhone on while you’re working on it.

Step 17

              Display Assembly

Remove the following Phillips screws:
Three 1.3 mm screws
One 1.6 mm screw
One 3.0 mm screw
During reassembly, it’s critical to place this 3.0 mm screw in the top-right corner of the bracket. Placing it anywhere else may damage the logic board.

Remove the following Phillips screws:

Three 1.3 mm screws

One 1.6 mm screw

One 3.0 mm screw

During reassembly, it’s critical to place this 3.0 mm screw in the top-right corner of the bracket. Placing it anywhere else may damage the logic board.

Step 18

Remove the display cable bracket.

Remove the display cable bracket.

Step 19

Be careful to only pry up on the connector itself and not the socket on the logic board.
Use a plastic opening tool to disconnect the front-facing camera and sensor cable connector.

Be careful to only pry up on the connector itself and not the socket on the logic board.

Use a plastic opening tool to disconnect the front-facing camera and sensor cable connector.

Step 20

Use a plastic opening tool to disconnect the digitizer cable by prying it straight up from its socket on the logic board.
When reconnecting the digitizer cable, do not press the center of the connector. Press one end of the connector, then press the opposite end. Pressing in the center of the connector can bend the component and cause digitizer damage.

Use a plastic opening tool to disconnect the digitizer cable by prying it straight up from its socket on the logic board.

When reconnecting the digitizer cable, do not press the center of the connector. Press one end of the connector, then press the opposite end. Pressing in the center of the connector can bend the component and cause digitizer damage.

Step 21

Make sure the battery is disconnected before you disconnect or reconnect the cable in this step.
Disconnect the home button/fingerprint sensor cable by prying it straight up from its socket on the logic board.

Make sure the battery is disconnected before you disconnect or reconnect the cable in this step.

Disconnect the home button/fingerprint sensor cable by prying it straight up from its socket on the logic board.

Step 22

Remove the display assembly.
During reassembly, pause here if you wish to replace the adhesive around the edges of the display.

Remove the display assembly.

During reassembly, pause here if you wish to replace the adhesive around the edges of the display.

Step 23

              Remove the stretch-release adhesive

Use tweezers, or your fingers, to peel up the black pull tab on one of the adhesive strips.
Take care not to puncture or bend the battery with your tool—a punctured or bent battery may leak dangerous chemicals or cause a fire.

Use tweezers, or your fingers, to peel up the black pull tab on one of the adhesive strips.

Take care not to puncture or bend the battery with your tool—a punctured or bent battery may leak dangerous chemicals or cause a fire.

Step 24

Pull the strip out slowly and steadily at a low angle. Give it plenty of time to stretch and un-stick from under the battery.
If the adhesive strip breaks off, try to retrieve it using your fingers or blunt tweezers, and continue pulling—but don’t pry under the battery.
You can optionally wrap the pull-tabs around a spudger to make it easier to pull out the adhesive strip.
Repeat the process for the remaining stretch release adhesive strips.
If the adhesive breaks off underneath the battery and can’t be retrieved, continue with the next step.

Pull the strip out slowly and steadily at a low angle. Give it plenty of time to stretch and un-stick from under the battery.

If the adhesive strip breaks off, try to retrieve it using your fingers or blunt tweezers, and continue pulling—but don’t pry under the battery.

You can optionally wrap the pull-tabs around a spudger to make it easier to pull out the adhesive strip.

Repeat the process for the remaining stretch release adhesive strips.

If the adhesive breaks off underneath the battery and can’t be retrieved, continue with the next step.

Step 25

              How to remove a stuck battery

If you’re still having trouble removing the battery, apply a few drops of high concentration (90% or higher) isopropyl alcohol under the edge of the battery in the area of the broken adhesive strip(s).
Tilt the phone up so the isopropyl alcohol can flow toward the adhesive strip.
Hold for 1–2 minutes to allow the isopropyl alcohol to weaken the adhesive.
Use an opening pick or the flat end of a spudger to slowly pry up the battery.

If you’re still having trouble removing the battery, apply a few drops of high concentration (90% or higher) isopropyl alcohol under the edge of the battery in the area of the broken adhesive strip(s).

Tilt the phone up so the isopropyl alcohol can flow toward the adhesive strip.

Hold for 1–2 minutes to allow the isopropyl alcohol to weaken the adhesive.

Use an opening pick or the flat end of a spudger to slowly pry up the battery.

Step 26

Remove the battery.
If your replacement battery came in a plastic sleeve, remove the sleeve before installation by pulling it away from the the ribbon cable.
If there’s any alcohol solution remaining in the phone, carefully wipe it off or allow it to air dry before installing your new battery.
Before you adhere the replacement battery, temporarily reconnect the battery connector to the logic board socket. This ensures that the battery is properly aligned in its recess.
Adhere the battery, disconnect it, and continue reassembling your device.
If your new battery doesn’t have adhesive preinstalled, refer to this guide to replace the adhesive strips.
Perform a hard reset after reassembly. This can prevent several issues and simplify troubleshooting.

Remove the battery.

If your replacement battery came in a plastic sleeve, remove the sleeve before installation by pulling it away from the the ribbon cable.

If there’s any alcohol solution remaining in the phone, carefully wipe it off or allow it to air dry before installing your new battery.

Before you adhere the replacement battery, temporarily reconnect the battery connector to the logic board socket. This ensures that the battery is properly aligned in its recess.

Adhere the battery, disconnect it, and continue reassembling your device.

If your new battery doesn’t have adhesive preinstalled, refer to this guide to replace the adhesive strips.

Perform a hard reset after reassembly. This can prevent several issues and simplify troubleshooting.

Step 27

              Volume Control Cable

Remove the two 2.7 mm Phillips screws over the audio control cable bracket.

Remove the two 2.7 mm Phillips screws over the audio control cable bracket.

Step 28

Remove the audio control cable bracket.

Remove the audio control cable bracket.

Step 29

Disconnect the audio control flex cable from its socket on the logic board.

Disconnect the audio control flex cable from its socket on the logic board.

Step 30

Remove the circular sticker covering the third screw securing the cellular antenna to the rear case.

Remove the circular sticker covering the third screw securing the cellular antenna to the rear case.

Step 31

Remove the following three Phillips screws:
One 2.7 mm screw
One 1.7 mm screw
One 1.3 mm screw

Remove the following three Phillips screws:

One 2.7 mm screw

One 1.7 mm screw

One 1.3 mm screw

Step 32

Lift, but do not remove, the cellular antenna to reveal the third screw securing the audio control cable to the rear case.

Lift, but do not remove, the cellular antenna to reveal the third screw securing the audio control cable to the rear case.

Step 33

Remove the three 2.4 mm Phillips screws over the audio control cable bracket.

Remove the three 2.4 mm Phillips screws over the audio control cable bracket.

Step 34

Use the flat end of a spudger to peel the volume control flex cable off the rear case.

Use the flat end of a spudger to peel the volume control flex cable off the rear case.

Step 35

Remove the volume control flex cable.
The cable assembly has two separate pieces connected by a ribbon cable—the volume control buttons and silent switch.

Remove the volume control flex cable.

The cable assembly has two separate pieces connected by a ribbon cable—the volume control buttons and silent switch.

Cancel: I did not complete this guide.

                                                                                      13 other people completed this guide.

Author

                                      with 6 other contributors

                    Dante Mazzanti

Member since: 07/13/2015

35,785 Reputation

                                      26 Guides authored                  



                       Badges:
                       34







                                                        +31 more badges

Introduction#

What you need#

Introduction

What you need