Iphone 14 Pro Lidar Sensor Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          50 minutes - 1 hour

Sections

Pentalobe Screw
1 step
Screen
16 steps
Rear-Facing Camera Assembly
6 steps
Lidar Sensor
5 steps

Flags

BackiPhone 14 Pro
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

This guide was created using the A2890 (international) model. If you’re fixing a different iPhone 14 Pro model, there may be some visual discrepancies, but the procedure should be the same.

You’ll need replacement adhesive to reattach the screen when reassembling the device. Your device will function normally, but will most likely lose its IP (Ingress Protection) rating.

What you need

Step 1

              Remove the pentalobe screws

Power off your iPhone before beginning disassembly.
Remove the two 6.8 mm-long pentalobe P2 screws at the bottom edge of the iPhone.

Power off your iPhone before beginning disassembly.

Remove the two 6.8 mm-long pentalobe P2 screws at the bottom edge of the iPhone.

1024

Step 2

              Heat the bottom edge of the iPhone

Heating the lower edge of the iPhone helps soften the adhesive securing the screen, making it easier to open.
Apply a heated iOpener to the bottom edge of the screen to loosen the adhesive underneath. Apply the iOpener for at least 2 minutes.
A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the device. The edge should feel slightly too hot to the touch.

Heating the lower edge of the iPhone helps soften the adhesive securing the screen, making it easier to open.

Apply a heated iOpener to the bottom edge of the screen to loosen the adhesive underneath. Apply the iOpener for at least 2 minutes.

A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the device. The edge should feel slightly too hot to the touch.

Step 3

              Insert an opening pick

Apply a suction handle to the bottom edge of the screen, while avoiding the very edge of the glass.
Pull up on the suction handle with firm, constant pressure to create a slight gap between the front panel and rear case.
Insert an opening pick into the gap.
The adhesive holding the screen in place is very strong; creating this initial gap takes a significant amount of force. If you’re having a hard time opening a gap, apply more heat, and gently rock the screen up and down to weaken the adhesive until you create enough of a gap to insert your opening pick.

Apply a suction handle to the bottom edge of the screen, while avoiding the very edge of the glass.

Pull up on the suction handle with firm, constant pressure to create a slight gap between the front panel and rear case.

Insert an opening pick into the gap.

The adhesive holding the screen in place is very strong; creating this initial gap takes a significant amount of force. If you’re having a hard time opening a gap, apply more heat, and gently rock the screen up and down to weaken the adhesive until you create enough of a gap to insert your opening pick.

Step 4

              Heat and separate the screen adhesive

Apply a heated iOpener to the left edge of the screen to loosen the adhesive underneath. Apply the iOpener for at least 2 minutes.

Apply a heated iOpener to the left edge of the screen to loosen the adhesive underneath. Apply the iOpener for at least 2 minutes.

Step 5

              Slice the left edge adhesive

Slide the opening pick around the lower left corner and up the left edge of the iPhone, slicing through the adhesive holding the screen in place.
Don’t insert the pick more than 3 mm inside your phone, or you may damage the display cables.

Slide the opening pick around the lower left corner and up the left edge of the iPhone, slicing through the adhesive holding the screen in place.

Don’t insert the pick more than 3 mm inside your phone, or you may damage the display cables.

Step 6

              Heat and separate the screen adhesive

Apply a heated iOpener to the right edge of the screen to loosen the adhesive underneath. Apply the iOpener for at least 2 minutes.

Apply a heated iOpener to the right edge of the screen to loosen the adhesive underneath. Apply the iOpener for at least 2 minutes.

Step 7

              Slice the right edge adhesive

Re-insert your pick at the bottom edge of the iPhone, and slide it up the right side to continue separating the adhesive.
Don’t insert the opening pick more than 3 mm into the iPhone, or you may cause damage to internal components.

Re-insert your pick at the bottom edge of the iPhone, and slide it up the right side to continue separating the adhesive.

Don’t insert the opening pick more than 3 mm into the iPhone, or you may cause damage to internal components.

Step 8

              Heat the top edge of the iPhone

Apply a heated iOpener to the top edge of the screen to loosen the adhesive underneath. Apply the iOpener for at least 2 minutes.

Apply a heated iOpener to the top edge of the screen to loosen the adhesive underneath. Apply the iOpener for at least 2 minutes.

Step 9

              Slice the top edge adhesive

Insert your pick underneath the top right edge of the phone. Slide it around the top-right corner and half way across the top edge stopping right before the earpiece speaker cut-out.
Don’t insert the pick more than 2 mm or you may damage the front panel sensor array.

Insert your pick underneath the top right edge of the phone. Slide it around the top-right corner and half way across the top edge stopping right before the earpiece speaker cut-out.

Don’t insert the pick more than 2 mm or you may damage the front panel sensor array.

Step 10

Insert your pick underneath the top-left edge of the phone. Slide it around the top-left corner and half way across the top edge stopping right before the earpiece speaker cut-out.
Again, don’t insert the pick more than 3 mm or you may damage the front panel sensor array.
Don’t try to fully separate the screen yet, as several fragile ribbon cables still connect it to the iPhone’s logic board.

Insert your pick underneath the top-left edge of the phone. Slide it around the top-left corner and half way across the top edge stopping right before the earpiece speaker cut-out.

Again, don’t insert the pick more than 3 mm or you may damage the front panel sensor array.

Don’t try to fully separate the screen yet, as several fragile ribbon cables still connect it to the iPhone’s logic board.

Step 11

              Open the iPhone

Remove your suction handle from the screen.
Open your iPhone by swinging the screen up from the right side, like the front cover of a book.
Lean the screen against something to keep it propped up while you’re working on the phone.
If you don’t have anything at hand to lean the screen against, your suction handle can do the trick.
During reassembly, lay the screen in position, align the clips along the top edge, and carefully press the top edge into place before snapping the rest of the screen down. If it doesn’t click easily into place, check the condition of the clips around the perimeter of the screen and make sure they aren’t bent.

Remove your suction handle from the screen.

Open your iPhone by swinging the screen up from the right side, like the front cover of a book.

Lean the screen against something to keep it propped up while you’re working on the phone.

If you don’t have anything at hand to lean the screen against, your suction handle can do the trick.

During reassembly, lay the screen in position, align the clips along the top edge, and carefully press the top edge into place before snapping the rest of the screen down. If it doesn’t click easily into place, check the condition of the clips around the perimeter of the screen and make sure they aren’t bent.

Step 12

              Unfasten the battery connector cover screws

Use a Y000 screwdriver to remove the eight screws securing the battery connector cover:
Six 1.3 mm-long screws
One 1.6 mm-long screw
One 1.9 mm-long screw
Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from to avoid damaging your iPhone.
During reassembly, this is a good point to power on your iPhone and test all functions before you seal the screen in place. Be sure to power your iPhone back down completely before you continue working.

Use a Y000 screwdriver to remove the eight screws securing the battery connector cover:

Six 1.3 mm-long screws

One 1.6 mm-long screw

One 1.9 mm-long screw

Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from to avoid damaging your iPhone.

During reassembly, this is a good point to power on your iPhone and test all functions before you seal the screen in place. Be sure to power your iPhone back down completely before you continue working.

Step 13

              Remove the battery connector cover

Grasp the connector cover with a pair of tweezers and slide it downwards to clear the flex cables.
Remove the connector cover.

Grasp the connector cover with a pair of tweezers and slide it downwards to clear the flex cables.

Remove the connector cover.

Step 14

              Disconnect the battery

Use the pointed end of a spudger to disconnect the battery cable by prying the connector straight up from its socket.
Try not to damage the black silicone seal surrounding this and other board connections. These seals provide extra protection against water and dust intrusion.
Bend the connector slightly away from the logic board to prevent it from accidentally making contact with the socket and providing power to the phone during your repair.

Use the pointed end of a spudger to disconnect the battery cable by prying the connector straight up from its socket.

Try not to damage the black silicone seal surrounding this and other board connections. These seals provide extra protection against water and dust intrusion.

Bend the connector slightly away from the logic board to prevent it from accidentally making contact with the socket and providing power to the phone during your repair.

Step 15

              Disconnect the display cable

Use the pointed end of a spudger to disconnect the first display cable by prying the connector straight up from its socket.
To re-attach press connectors like this one, carefully align and press down on one side until it clicks into place, then repeat on the other side. Do not press down on the middle. If the connector is misaligned, the pins can bend, causing permanent damage.

Use the pointed end of a spudger to disconnect the first display cable by prying the connector straight up from its socket.

To re-attach press connectors like this one, carefully align and press down on one side until it clicks into place, then repeat on the other side. Do not press down on the middle. If the connector is misaligned, the pins can bend, causing permanent damage.

Step 16

Use the pointed end of a spudger to disconnect the second display cable by prying the connector straight up from its socket.

Use the pointed end of a spudger to disconnect the second display cable by prying the connector straight up from its socket.

Step 17

              Remove the screen

Remove the screen.
Apply new adhesive where it’s necessary after cleaning the relevant areas with isopropyl alcohol (>90%).
During reassembly, pause here if you wish to replace the screen adhesives.

Remove the screen.

Apply new adhesive where it’s necessary after cleaning the relevant areas with isopropyl alcohol (>90%).

During reassembly, pause here if you wish to replace the screen adhesives.

Step 18

              Unfasten the rear-facing camera assembly cover screws

Use a Y000 driver to remove the five screws securing the rear-facing camera assembly cover:
Four 1.5 mm-long Y000 screws
One 1.3 mm-long Y000 screw
Use a Phillips screwdriver to remove one 1.7 mm-long screw.

Use a Y000 driver to remove the five screws securing the rear-facing camera assembly cover:

Four 1.5 mm-long Y000 screws

One 1.3 mm-long Y000 screw

Use a Phillips screwdriver to remove one 1.7 mm-long screw.

Step 19

              Remove the rear-facing camera assembly cover

There’s a small metal edge in the top right corner of the rear-facing camera assembly cover that is secured by the phone frame.
Grab the rear-facing camera assembly cover with a pair of tweezers.
Move the rear-facing camera assembly cover toward the volume buttons to free its small metal edge from the frame.
Remove the rear-facing camera assembly cover.
During reassembly, make sure to align the rear-facing camera assembly cover correctly and push the small metal edge back into its recess in the frame.

There’s a small metal edge in the top right corner of the rear-facing camera assembly cover that is secured by the phone frame.

Grab the rear-facing camera assembly cover with a pair of tweezers.

Move the rear-facing camera assembly cover toward the volume buttons to free its small metal edge from the frame.

Remove the rear-facing camera assembly cover.

During reassembly, make sure to align the rear-facing camera assembly cover correctly and push the small metal edge back into its recess in the frame.

Step 20

              Disconnect the ultra wide and telephoto camera cable

Use a spudger to disconnect the ultra wide and telephoto lens cable by prying the connector straight up from its socket.

Use a spudger to disconnect the ultra wide and telephoto lens cable by prying the connector straight up from its socket.

Step 21

              Disconnect the wide lens camera cable

Use a spudger to disconnect the wide lens cable by prying the connector straight up from its socket.

Use a spudger to disconnect the wide lens cable by prying the connector straight up from its socket.

Step 22

              Pry up the rear-facing camera assembly

Insert the pointed end of a spudger underneath the bottom edge of the rear-facing camera assembly.
Pry up with the spudger to loosen the rear-facing camera assembly.

Insert the pointed end of a spudger underneath the bottom edge of the rear-facing camera assembly.

Pry up with the spudger to loosen the rear-facing camera assembly.

Step 23

              Remove the rear-facing camera assembly

Use a pair of tweezers or your fingers to remove the rear-facing camera assembly.

Use a pair of tweezers or your fingers to remove the rear-facing camera assembly.

Step 24

              Unfasten the lidar sensor cover screw

Use a standoff screwdriver to remove the 2.8 mm-long standoff screw securing the lidar sensor cover.

Use a standoff screwdriver to remove the 2.8 mm-long standoff screw securing the lidar sensor cover.

Step 25

              Remove the lidar sensor cover

Use a pair of tweezers to remove the lidar sensor cover.

Use a pair of tweezers to remove the lidar sensor cover.

Step 26

              Disconnect the lidar sensor

Use a spudger to disconnect the lidar sensor cable by prying the connector straight up from its socket.

Use a spudger to disconnect the lidar sensor cable by prying the connector straight up from its socket.

Step 27

              Pry up the lidar sensor

Insert the flat end of a spudger underneath the top edge of the lidar sensor.
Pry up with the spudger to loosen the lidar sensor.

Insert the flat end of a spudger underneath the top edge of the lidar sensor.

Pry up with the spudger to loosen the lidar sensor.

Step 28

              Remove the lidar sensor

Use a pair of tweezers to remove the lidar sensor.

Use a pair of tweezers to remove the lidar sensor.

If possible, turn on your device and test your repair before installing new adhesive and resealing.

Compare your new replacement part to the original part—you may need to transfer remaining components or remove adhesive backings from the new part before installing.

To reassemble your device, follow these instructions in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our Answers community for help.

Cancel: I did not complete this guide.

Author

                    Manuel Haeussermann

Member since: 07/13/2022

4,291 Reputation

                                      28 Guides authored                  



                       Badges:
                       22







                                                        +19 more badges

Team

                       iFixit                        

                                                  Member of iFixit 



                    Community                     


                                            141 Members                     


                                            15,772 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team