Ipad Wi Fi Speakers Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

Suggest a time??

Sections

Display Assembly
10 steps
Dock Connector Cable
5 steps
Speakers
5 steps

Flags

BackiPad Wi-Fi
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Display Assembly

If your display glass is cracked, keep further breakage contained and prevent bodily harm during your repair by taping the glass.
Lay overlapping strips of clear packing tape over the iPad’s display until the whole face is covered.
This will keep glass shards contained and provide structural integrity when prying and lifting the display.
Do your best to follow the rest of the guide as described. However, once the glass is broken, it will likely continue to crack as you work, and you may need to use a metal prying tool to scoop the glass out.
Wear safety glasses to protect your eyes, and be careful not to damage the LCD screen.

If your display glass is cracked, keep further breakage contained and prevent bodily harm during your repair by taping the glass.

Lay overlapping strips of clear packing tape over the iPad’s display until the whole face is covered.

This will keep glass shards contained and provide structural integrity when prying and lifting the display.

Do your best to follow the rest of the guide as described. However, once the glass is broken, it will likely continue to crack as you work, and you may need to use a metal prying tool to scoop the glass out.

Wear safety glasses to protect your eyes, and be careful not to damage the LCD screen.

1024

Step 2

In this guide you will be prying the iPad’s display assembly away from the aluminum body. Read ahead and follow the directions closely to avoid damaging the display assembly or the fragile clips holding it in place.
There are 14 metal clips holding the display assembly in place, shown at left. As you pry in the following steps, do your best to pry around these clips and not slice through them with your opening tool.
If you do happen to break some clips, you can buy replacements here.

In this guide you will be prying the iPad’s display assembly away from the aluminum body. Read ahead and follow the directions closely to avoid damaging the display assembly or the fragile clips holding it in place.

There are 14 metal clips holding the display assembly in place, shown at left. As you pry in the following steps, do your best to pry around these clips and not slice through them with your opening tool.

If you do happen to break some clips, you can buy replacements here.

Step 3

Insert a metal spudger between the top edge of the display assembly and the rear panel assembly.
Rotate the spudger away from you to release the tabs along the top edge of the display.
Insert a second metal spudger between the top edge of the display assembly and the rear panel assembly to keep the tabs from snapping back into place.

Insert a metal spudger between the top edge of the display assembly and the rear panel assembly.

Rotate the spudger away from you to release the tabs along the top edge of the display.

Insert a second metal spudger between the top edge of the display assembly and the rear panel assembly to keep the tabs from snapping back into place.

Step 4

With one spudger, work your way along the right edge of the iPad.
The front panel is held to the aluminum back by metal clips on the top, bottom, and left sides. The right side has plastic tabs which slide into recesses in the backplate.
Once the clips are released, lift the left side of the front panel up and slide it to the left to clear the tabs from the aluminum backplate.
Pry carefully and gently—if you feel resistance, stop and pry at another spot.

With one spudger, work your way along the right edge of the iPad.

The front panel is held to the aluminum back by metal clips on the top, bottom, and left sides. The right side has plastic tabs which slide into recesses in the backplate.

Once the clips are released, lift the left side of the front panel up and slide it to the left to clear the tabs from the aluminum backplate.

Pry carefully and gently—if you feel resistance, stop and pry at another spot.

Step 5

Lift the display assembly away from the rear panel assembly by its bottom edge.
Do not attempt to remove the display at this time, as it is attached to the rear panel assembly.

Lift the display assembly away from the rear panel assembly by its bottom edge.

Do not attempt to remove the display at this time, as it is attached to the rear panel assembly.

Step 6

In the following steps, you will disconnect the three cables attaching the display assembly to the logic board. The cables are for the following components:
Digitizer
Ambient Light Sensor
Display Data Cable

In the following steps, you will disconnect the three cables attaching the display assembly to the logic board. The cables are for the following components:

Digitizer

Ambient Light Sensor

Display Data Cable

Step 7

Use the edge of a plastic opening tool to flip up the retaining flaps holding the digitizer ribbon cables in their sockets on the logic board.
Be sure you are flipping up the retaining flap, not the socket itself.
Pull the digitizer ribbon cables straight out of their sockets.

Use the edge of a plastic opening tool to flip up the retaining flaps holding the digitizer ribbon cables in their sockets on the logic board.

Be sure you are flipping up the retaining flap, not the socket itself.

Pull the digitizer ribbon cables straight out of their sockets.

Step 8

Use a plastic opening tool to remove the ambient light sensor connector from its socket by gently prying upward.

Use a plastic opening tool to remove the ambient light sensor connector from its socket by gently prying upward.

Step 9

Disconnect the display data cable from the main board by flipping up the metal retainer by its black plastic pull tab.
Pull the cable connector away from its socket.
Pull the connector parallel to the face of the logic board.

Disconnect the display data cable from the main board by flipping up the metal retainer by its black plastic pull tab.

Pull the cable connector away from its socket.

Pull the connector parallel to the face of the logic board.

Step 10

Remove the display assembly from the rear panel assembly.

Remove the display assembly from the rear panel assembly.

Step 11

              Dock Connector Cable

Remove the two 4.56 mm T5 Torx screws securing the dock connector cable to the main board.

Remove the two 4.56 mm T5 Torx screws securing the dock connector cable to the main board.

Step 12

Remove the single 2.84 mm T5 Torx screw connecting the dock connector cable to the rear case assembly.

Remove the single 2.84 mm T5 Torx screw connecting the dock connector cable to the rear case assembly.

Step 13

Remove the two 2.84 mm T5 Torx screws securing the dock connector cable to the rear panel assembly.

Remove the two 2.84 mm T5 Torx screws securing the dock connector cable to the rear panel assembly.

Step 14

Carefully remove the plastic cover over the WiFi/Bluetooth board and dock connector cable using a plastic opening tool.

Carefully remove the plastic cover over the WiFi/Bluetooth board and dock connector cable using a plastic opening tool.

Step 15

Pry the Wi-Fi and Bluetooth antennas up off their respective sockets on the Wi-Fi/Bluetooth board.
Remove the dock connector cable from the rear panel assembly.

Pry the Wi-Fi and Bluetooth antennas up off their respective sockets on the Wi-Fi/Bluetooth board.

Remove the dock connector cable from the rear panel assembly.

Step 16

              Speakers

Use the edge of a plastic opening tool to disconnect the speaker connector from the logic board.
Pry up from beneath the wires.

Use the edge of a plastic opening tool to disconnect the speaker connector from the logic board.

Pry up from beneath the wires.

Step 17

Remove the two 2.84 mm T5 Torx screws securing the speaker assembly to the rear panel assembly.
If necessary, remove the tape covering the Wi-Fi cables.

Remove the two 2.84 mm T5 Torx screws securing the speaker assembly to the rear panel assembly.

If necessary, remove the tape covering the Wi-Fi cables.

Step 18

De-route the Wi-Fi antenna through its channel in the speaker assembly.

De-route the Wi-Fi antenna through its channel in the speaker assembly.

Step 19

Deroute the speaker cable connector through the left side of the rear panel assembly.

Deroute the speaker cable connector through the left side of the rear panel assembly.

Step 20

Lift the speaker assembly and push it forward until the ports clear the bottom side of the rear panel assembly.
Remove the speaker assembly out of the rear panel assembly.

Lift the speaker assembly and push it forward until the ports clear the bottom side of the rear panel assembly.

Remove the speaker assembly out of the rear panel assembly.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      5 other people completed this guide.

Author

                                      with 8 other contributors

                    Miroslav Djuric

156,282 Reputation

                                      144 Guides authored                  



                       Badges:
                       54







                                                        +51 more badges

Introduction#

What you need#

Introduction

What you need