Difficulty

Easy

Steps

5

Time Required

                          30 seconds

Sections

2

  • iOpener Heating
  • 4 steps
  • iOpener Instructions
  • 1 step

Flags

0

  • BackiOpener

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

Follow these basic instructions to get started with your new (black, liquid-filled) iOpener. For the white, solid-filled iOpener, follow this guide instead.

For detailed instructions specific to your device and repair, see our set of iPad repair guides.

What you need

Step 1

              iOpener Heating
  • We recommend that you clean your microwave before proceeding, as any nasty gunk on the bottom may end up stuck to the iOpener.
  • Place the iOpener in the center of the microwave.
  • For carousel microwaves: Make sure the plate spins freely. If your iOpener gets stuck, it may overheat and burn.

We recommend that you clean your microwave before proceeding, as any nasty gunk on the bottom may end up stuck to the iOpener.

Place the iOpener in the center of the microwave.

For carousel microwaves: Make sure the plate spins freely. If your iOpener gets stuck, it may overheat and burn.

1024

Step 2

  • Heat the iOpener for thirty seconds.
  • Throughout the repair procedure, as the iOpener cools, reheat it in the microwave for an additional thirty seconds at a time.
  • Be careful not to overheat the iOpener during the repair. Overheating may cause the iOpener to burst.
  • Never touch the iOpener if it appears swollen.
  • If the iOpener is still too hot in the middle to touch, continue using it while waiting for it to cool down some more before reheating. A properly heated iOpener should stay warm for up to 10 minutes.

Heat the iOpener for thirty seconds.

Throughout the repair procedure, as the iOpener cools, reheat it in the microwave for an additional thirty seconds at a time.

Be careful not to overheat the iOpener during the repair. Overheating may cause the iOpener to burst.

Never touch the iOpener if it appears swollen.

If the iOpener is still too hot in the middle to touch, continue using it while waiting for it to cool down some more before reheating. A properly heated iOpener should stay warm for up to 10 minutes.

Step 3

  • Remove the iOpener from the microwave, holding it by one of the two flat ends to avoid the hot center.
  • The iOpener will be very hot, so be careful when handling it. Use an oven mitt if necessary.

Remove the iOpener from the microwave, holding it by one of the two flat ends to avoid the hot center.

The iOpener will be very hot, so be careful when handling it. Use an oven mitt if necessary.

Step 4

              Alternate iOpener heating method
  • If you don’t have a microwave, follow this step to heat your iOpener in boiling water.
  • Fill a pot or pan with enough water to fully submerge an iOpener.
  • Heat the water to a boil. Turn off the heat.
  • Place an iOpener into the hot water for 2-3 minutes. Make sure the iOpener is fully submerged in the water.
  • Use tongs to extract the heated iOpener from the hot water.
  • Thoroughly dry the iOpener with a towel.
  • The iOpener will be very hot, so be careful to hold it only by the end tabs.
  • Your iOpener is ready for use! If you need to reheat the iOpener, heat the water to a boil, turn off the heat, and place the iOpener in the water for 2-3 minutes.

If you don’t have a microwave, follow this step to heat your iOpener in boiling water.

Fill a pot or pan with enough water to fully submerge an iOpener.

Heat the water to a boil. Turn off the heat.

Place an iOpener into the hot water for 2-3 minutes. Make sure the iOpener is fully submerged in the water.

Use tongs to extract the heated iOpener from the hot water.

Thoroughly dry the iOpener with a towel.

The iOpener will be very hot, so be careful to hold it only by the end tabs.

Your iOpener is ready for use! If you need to reheat the iOpener, heat the water to a boil, turn off the heat, and place the iOpener in the water for 2-3 minutes.

Step 5

              iOpener Instructions
  • Lay the iOpener clear-side down, flat on the edge of the device, over an adhesive seal you wish to heat. The liquid will flatten the iOpener against the surface, ensuring good heat conduction.
  • Let the bag sit on the device for approximately 90 seconds before attempting to open the front panel.
  • At this point you should be able to begin prying under the screen with a plastic opening tool. Be sure to see your device’s specific guide for where and how to do this.
  • During the procedure you may need to reheat the iOpener. To prevent overheating the iOpener, always wait until the iOpener has cooled enough to touch safely. Do not microwave the iOpener for more than thirty seconds at a time.

Lay the iOpener clear-side down, flat on the edge of the device, over an adhesive seal you wish to heat. The liquid will flatten the iOpener against the surface, ensuring good heat conduction.

Let the bag sit on the device for approximately 90 seconds before attempting to open the front panel.

At this point you should be able to begin prying under the screen with a plastic opening tool. Be sure to see your device’s specific guide for where and how to do this.

During the procedure you may need to reheat the iOpener. To prevent overheating the iOpener, always wait until the iOpener has cooled enough to touch safely. Do not microwave the iOpener for more than thirty seconds at a time.

Cancel: I did not complete this guide.

                                                                                      523 other people completed this guide.

Author

                                      with 7 other contributors 


                    Andrew Optimus Goldheart

Member since: 10/17/2009

491,689 Reputation

                                      411 Guides authored                  



                       Badges:
                       44







                                                        +41 more badges

Team

                       iFixit                        

                                                  Member of iFixit 



                    Community                     


                                            141 Members                     


                                            15,767 Guides authored

Kevin McCartney - Jan 31, 2014

Reply

I bought two of these, and I can’t get an iPad 2 to open using the iOpener; I’m going to keep trying, but heads up, it’s not as easy as 1-2-3. I’ll update if I get it to work.

Chris Newman - Feb 11, 2019

I used a flat toaster maker and turned it off and on as required, Fixed my Ipad mini ok.

Mark Brown - Dec 17, 2015

Reply

Step 2 says to wait 5 minutes between reheating, step 4 says to wait 3 minutes.

Also, do you sell the “this is a microwave” stickers? xD

allanwl - Feb 21, 2016

Reply

Will this tool damage the lcd/ pixels or even the camera/sensor if placed on the edge above those? I need to soften up the adhesive only, not replacing the screen at all. I have a surface pro 4.

Steven Aigner - Aug 14, 2016

Reply

A short remark about how much force will then be needed to separate the old battery from the heated adhesive would be helpful. I found that even after I was able to begin the insertion of a plastic card between the battery and the case, it required a great deal of force to push the card further under the battery to complete the separation.