Difficulty
Very easy
Steps
7
Time Required
5 minutes
Sections
3
- Battery
- 4 steps
- Motherboard
- 2 steps
- Lens
- 1 step
Flags
0
BackiON SnapCam 1045
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Detach the magnetic clip from the bottom of the camera.
- The magnetic clip gets in the way of disassembly because it constantly spins and therefore a distraction so it is imperative to detach.
Detach the magnetic clip from the bottom of the camera.
The magnetic clip gets in the way of disassembly because it constantly spins and therefore a distraction so it is imperative to detach.
1024
Step 2
- Use a spudger to gently detach the memory card and USB slot cover.
Use a spudger to gently detach the memory card and USB slot cover.
Step 3
- Use a Phillips #000 Screwdriver to loosen the 0.008 mm screw located between the USB and memory card slots.
- This screw is really tiny and can easily fall off and get lost! Make use of a magnetic mat to hold it in place or better still put the magnetic clip to use for keeping the screw safe.
Use a Phillips #000 Screwdriver to loosen the 0.008 mm screw located between the USB and memory card slots.
This screw is really tiny and can easily fall off and get lost! Make use of a magnetic mat to hold it in place or better still put the magnetic clip to use for keeping the screw safe.
Step 4
- Once again use the spudger to gently open the encasement.
- The case is a little fragile and forceful entry could lead to damage of the plastic case. Thread carefully.
- The Battery can be safely detached and replaced.
Once again use the spudger to gently open the encasement.
The case is a little fragile and forceful entry could lead to damage of the plastic case. Thread carefully.
The Battery can be safely detached and replaced.
Step 5
Motherboard
- To get to the motherboard, safely lift the battery to expose an Aluminium plate that shields and holds the motherboard in place.
- The plates are held down by four Phillips 0.008 mm screws on all four corners. Use a Phillips head #000 to safely loosen the screws.
To get to the motherboard, safely lift the battery to expose an Aluminium plate that shields and holds the motherboard in place.
The plates are held down by four Phillips 0.008 mm screws on all four corners. Use a Phillips head #000 to safely loosen the screws.
Step 6
- To replace the motherboard gently insert a plastic opening tool into one end and lift up.
- Be careful to avoid inserting material that is rough and too sturdy as it can damage components on the motherboard.
To replace the motherboard gently insert a plastic opening tool into one end and lift up.
Be careful to avoid inserting material that is rough and too sturdy as it can damage components on the motherboard.
Step 7
Lens
- The motherboard is in plain sight . The lens assembly is located on the lower left part of the motherboard just to the left of the power button.
- To replace the lens assembly, simply flip it up and detach.
The motherboard is in plain sight . The lens assembly is located on the lower left part of the motherboard just to the left of the power button.
To replace the lens assembly, simply flip it up and detach.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 3 other contributors
Jessica Matias
Member since: 12/09/2017
201 Reputation
2 Guides authored
Badges:
3
Team
IUPUI, Team S3-G3, Wilson Fall 2017
Member of IUPUI, Team S3-G3, Wilson Fall 2017
IUPUI-WILSON-F17S3G3
3 Members
3 Guides authored
