Difficulty

Moderate

Steps

8

Time Required

                          10 - 15 minutes

Sections

1

  • Body Cover
  • 8 steps

Flags

Bullets!

Better coordination with markups and the color/type of bullets will help make this guide more clear!

  • BackIon Air Pro

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Body Cover
  • Unscrew all six screws.
  • Make sure you put the screws in a good spot where you won’t lose them because they are small.

Unscrew all six screws.

Make sure you put the screws in a good spot where you won’t lose them because they are small.

1024

Step 2

  • After you’re done with unscrewing, take off the blue lid shown here.

After you’re done with unscrewing, take off the blue lid shown here.

Step 3

  • Next, on the other side of the device, you would lift this black piece of cover that is underneath the cap, on the bottom side of the Ion Air Pro.

Next, on the other side of the device, you would lift this black piece of cover that is underneath the cap, on the bottom side of the Ion Air Pro.

Step 4

  • After removing the black lid off, you have to unscrew all eight screws here.
  • Again make sure you keep track of your screws and don’t lose them.

After removing the black lid off, you have to unscrew all eight screws here.

Again make sure you keep track of your screws and don’t lose them.

Step 5

  • After unscrewing all eight screws, there are two more screws, one on each side, inside this socket that you will have to remove as well.

After unscrewing all eight screws, there are two more screws, one on each side, inside this socket that you will have to remove as well.

Step 6

  • Next, you would want to unscrew the two screws located here.

Next, you would want to unscrew the two screws located here.

Step 7

  • You could then detach the bottom black piece off from the bottom side but do not disconnect it from the wires.
  • Everything inside is still connected with all the wires in there so be careful not to pull too hard or else everything inside could fall out or get broken.

You could then detach the bottom black piece off from the bottom side but do not disconnect it from the wires.

Everything inside is still connected with all the wires in there so be careful not to pull too hard or else everything inside could fall out or get broken.

Step 8

  • Finally, you can remove the body cover off and replace it with a new one if you have to.

Finally, you can remove the body cover off and replace it with a new one if you have to.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 3 other contributors 


                    Christopher Brandl

Member since: 10/09/2018

673 Reputation

                                      5 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       UW Stout, Team S6-G2, Ogden Fall 2018                        

                                                  Member of UW Stout, Team S6-G2, Ogden Fall 2018 



                    UWSTOUT-OGDEN-F18S6G2                     


                                            4 Members                     


                                            5 Guides authored

Sam s - Jan 5, 2019

Reply

Hey Chris where can I buy a replacement body cover?

The thread of the screw socket on my ion air pro WiFi has worn out and it can no longer be screwed onto any mounts.

mcbee1010 - Nov 10, 2019

Reply

I LOST THE LOSTTHE REAR COVER WHILE HUNTING. iS THERE A REPLACEMENT I CAN GET

i lost the rear cover cap while hunting. can i purchase a new one