Difficulty

Moderate

Steps

7

Time Required

                          10 minutes

Sections

1

  • LED Display
  • 7 steps

Flags

This guide has been the hard work of our awesome students and is found to be exceptionally cool by the iFixit staff.

  • BackInstant Pot Duo IP-DUO80 V2

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              LED Display
  • Open the lid by turning it counter-clockwise and lifting up.
  • Remove the inner pot.

Open the lid by turning it counter-clockwise and lifting up.

Remove the inner pot.

1024

Step 2

  • Turn the Instant Pot upside down.
  • Remove the single 12-mm screw by using the T-15 head screwdriver and turning it counter-clockwise.
  • Turn the plate counter-clockwise and lift it off the Instant Pot.

Turn the Instant Pot upside down.

Remove the single 12-mm screw by using the T-15 head screwdriver and turning it counter-clockwise.

Turn the plate counter-clockwise and lift it off the Instant Pot.

Step 3

  • Remove the three 19-mm screws in the black plastic base’s edge using the PH-1 head screwdriver and twisting counter-clockwise.

Remove the three 19-mm screws in the black plastic base’s edge using the PH-1 head screwdriver and twisting counter-clockwise.

Step 4

  • Pull the power cord out of its slot.
  • Pull up on the edge of the black plastic base to remove the base.

Pull the power cord out of its slot.

Pull up on the edge of the black plastic base to remove the base.

Step 5

  • Disconnect the two green-striped yellow wires that are connected onto the bottom of the heating element. Use a PH-1 head screwdriver and turn counter-clockwise to remove the 10-mm screw holding them in place.
  • Be careful not to lose the small washer that comes with this screw.
  • Pull up on the cn101 connection to detach the LED display from the motherboard.

Disconnect the two green-striped yellow wires that are connected onto the bottom of the heating element. Use a PH-1 head screwdriver and turn counter-clockwise to remove the 10-mm screw holding them in place.

Be careful not to lose the small washer that comes with this screw.

Pull up on the cn101 connection to detach the LED display from the motherboard.

Step 6

  • Lift the silver outer shell off of the top black ring.

Lift the silver outer shell off of the top black ring.

Step 7

  • Remove the two 10-mm screws connecting the LED display to the outer shell using a PH-1 head screwdriver and twisting counter clockwise.
  • Pull out the LED display by pulling on it gently.

Remove the two 10-mm screws connecting the LED display to the outer shell using a PH-1 head screwdriver and twisting counter clockwise.

Pull out the LED display by pulling on it gently.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      5 other people completed this guide.

Author

                                      with 3 other contributors 


                    Kayla Meacham

Member since: 01/23/2018

618 Reputation

                                      5 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       Cal Poly, Team S18-G2, Livingston Winter 2018                        

                                                  Member of Cal Poly, Team S18-G2, Livingston Winter 2018 



                    CPSU-LIVINGSTON-W18S18G2                     


                                            4 Members                     


                                            10 Guides authored

Starfish Doodle - Feb 21, 2019

Reply

Where can I get the replacement for the display?