Difficulty

Easy

Steps

10

Time Required

                          25 minutes

Sections

1

  • Fog Lamps
  • 10 steps

Flags

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

  • BackFord F-Series

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

What you need

Step 1

              Auer Automotive F-Series LED Projector Fog Lamps Part# 260-FFS-819
  • How to install Auer Automotive LED Projector Fog Lamps Part number 260-FFS-819
  • Note: Not applicable for Raptor
  • Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory should follow approved guidelines to ensure a quality installation.
  • “CAUTION: IT IS ADVISABLE TO DISCONNECT THE NEGATIVE BATTERY CABLE FOR 3 MINUTES BEFORE BEGINNING INSTALLATION, NOTE AND RECORD ANY ANTI- THEFT RADIO CODES PRIOR TO DISCONNECTING.’''

How to install Auer Automotive LED Projector Fog Lamps Part number 260-FFS-819

Note: Not applicable for Raptor

Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory should follow approved guidelines to ensure a quality installation.

“CAUTION: IT IS ADVISABLE TO DISCONNECT THE NEGATIVE BATTERY CABLE FOR 3 MINUTES BEFORE BEGINNING INSTALLATION, NOTE AND RECORD ANY ANTI- THEFT RADIO CODES PRIOR TO DISCONNECTING.’''

1024

Step 2

              Locate bulb connector
  • Locate Fog lamp bulb connector at rear of Lamp assembly.

Locate Fog lamp bulb connector at rear of Lamp assembly.

Step 3

              Remove Bulb
  • With index finger, rotate bulb connector clockwise 90 degrees to remove bulb.

With index finger, rotate bulb connector clockwise 90 degrees to remove bulb.

Step 4

              Remove bulb and disconnect from harness
  • Remove bulb from connector and place bulb to the side.

Remove bulb from connector and place bulb to the side.

Step 5

              Disconnect Lamp
  • Remove adjustment screw from lamp assembly and retain for new lamp.
  • NOTE: Take note of how many rotations to aid in lamp alignment after install of new lamp assembly.

Remove adjustment screw from lamp assembly and retain for new lamp.

NOTE: Take note of how many rotations to aid in lamp alignment after install of new lamp assembly.

Step 6

              Remove Existing Lamp
  • The lamp is retained into the bezel via two circular tabs in which the fog lamp will snap into. Insert a small flat head screwdriver between the lamp and the bezel on the left side from the front of the vehicle to pry bezel tab from lamp. Apply pressure from the rear to dislodge lamp, as seen in photo.

The lamp is retained into the bezel via two circular tabs in which the fog lamp will snap into. Insert a small flat head screwdriver between the lamp and the bezel on the left side from the front of the vehicle to pry bezel tab from lamp. Apply pressure from the rear to dislodge lamp, as seen in photo.

Step 7

              Remove Existing Lamp
  • Detach right side tab at rear of fog lamp, (as seen in photo) and push lamp forward

Detach right side tab at rear of fog lamp, (as seen in photo) and push lamp forward

Step 8

              Remove existing Lamp
  • Remove factory lamp by pushing forward through the bezel and remove from the front of vehicle.
  • Remove WHITE screw retention tab from factory fog and insert onto new lamp

Remove factory lamp by pushing forward through the bezel and remove from the front of vehicle.

Remove WHITE screw retention tab from factory fog and insert onto new lamp

Step 9

              Install new Auer Automotive LED Lamp
  • From the front of the vehicle, insert new Fog lamp into bezel and push until assembly snaps into bezel.

From the front of the vehicle, insert new Fog lamp into bezel and push until assembly snaps into bezel.

Step 10

              Install new Auer Automotive LED Lamp
  • Reinstall adjustment screw into retainer. (Once screw begins to compress spring, turn screw approx. 6 turns).
  • Connect harness connector.
  • Repeat above procedures for opposing lamp.
  • After both lamps have been installed, start vehicle to ensure proper operation and to check for proper beam alignment.
  • Park vehicle 8-10 feet from wall and check for proper beam alignment when installation is complete.
  • Utilize adjustment screws on lamp. (Clockwise to lower beam and counter clockwise to raise beam).

Reinstall adjustment screw into retainer. (Once screw begins to compress spring, turn screw approx. 6 turns).

Connect harness connector.

Repeat above procedures for opposing lamp.

After both lamps have been installed, start vehicle to ensure proper operation and to check for proper beam alignment.

Park vehicle 8-10 feet from wall and check for proper beam alignment when installation is complete.

Utilize adjustment screws on lamp. (Clockwise to lower beam and counter clockwise to raise beam).

If you have any questions or concerns with this installation guide, feel free to contact Auer Automotive at 904-374-6110 or email info@auerautomotive.com

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 1 other contributor 


                    Bill Skipper

Member since: 12/17/2018

211 Reputation

                                      1 Guide authored                  



                       Badges:
                       2