Difficulty
Moderate
Steps
12
Time Required
15 - 25 minutes
Sections
2
- Outer Panels
- 5 steps
- CD Laser Lens
- 7 steps
Flags
1
Needs Better Images
Better photos will improve this guide. Help out by taking, editing, or uploading new ones!
BackInsignia NS-BCDCAS1
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
Before attempting this replacement, make sure to use a anti-static strap to prevent circuit damages to your device.
What you need
Step 1
Outer Panels
- Turn the boombox around to see the back, and then flip it upside down.
- Insert a 2.5mm flathead driver into the two holes next to the battery compartment.
- Turn the driver counterclockwise several times to loosen and pull out the 17mm screw.
Turn the boombox around to see the back, and then flip it upside down.
Insert a 2.5mm flathead driver into the two holes next to the battery compartment.
Turn the driver counterclockwise several times to loosen and pull out the 17mm screw.
1024
Step 2
- Peel off the two black square foams in front of the battery compartment to reveal a screw under each one.
Peel off the two black square foams in front of the battery compartment to reveal a screw under each one.
Step 3
- Remove the two 8mm screws using a 2.5mm flathead driver.
- The front grey panel will loosen up once the final screw is removed.
Remove the two 8mm screws using a 2.5mm flathead driver.
The front grey panel will loosen up once the final screw is removed.
Step 4
- Turn the boombox on its back.
- Release the front panel by pushing down on the latches holding the panels together.
- There are four silver latches on the top side of the panel and one on the bottom.
- Do not force the panel comletely off, there are cables attached inside.
Turn the boombox on its back.
Release the front panel by pushing down on the latches holding the panels together.
There are four silver latches on the top side of the panel and one on the bottom.
Do not force the panel comletely off, there are cables attached inside.
Step 5
- Turn the boombox around to view the back and lift the handle up.
- Using the same driver with 2.5mm flathead, remove the two 14mm screws under the handle.
- Gently lift the black top but do not pull completely away.
Turn the boombox around to view the back and lift the handle up.
Using the same driver with 2.5mm flathead, remove the two 14mm screws under the handle.
Gently lift the black top but do not pull completely away.
Step 6
CD Laser Lens
- Unplug the red and black wires from the large yellow motherboard by pulling upwards.
Unplug the red and black wires from the large yellow motherboard by pulling upwards.
Step 7
- Unplug the thick, white and pink cord from underneath the black top by pulling downwards.
Unplug the thick, white and pink cord from underneath the black top by pulling downwards.
Step 8
- Remove the black shiny strip from both ends of the white motherboard adaptor.
Remove the black shiny strip from both ends of the white motherboard adaptor.
Step 9
- Using a Phillips #0, remove the two 11mm screws attached to the green legs underneath the top panel.
Using a Phillips #0, remove the two 11mm screws attached to the green legs underneath the top panel.
Step 10
- With a plastic opening tool, take off the red rings on the other two green legs.
- The red rings fall off easily once loosened.
With a plastic opening tool, take off the red rings on the other two green legs.
The red rings fall off easily once loosened.
Step 11
- Using a JIS 1, remove the 8mm screw on the grey, square plate.
Using a JIS 1, remove the 8mm screw on the grey, square plate.
Step 12
- Slide the silver bar out.
- Everything will be loosened. Support it with your hand
- The square cube with the tiny lense is loosened. Slide it down to take out of the nook.
- Detach the black tape so the cube is completely by itself. Replace the cube with a new one.
Slide the silver bar out.
Everything will be loosened. Support it with your hand
The square cube with the tiny lense is loosened. Slide it down to take out of the nook.
Detach the black tape so the cube is completely by itself. Replace the cube with a new one.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 4 other contributors
Erin King
Member since: 09/12/2016
215 Reputation
2 Guides authored
Badges:
6
+3 more badges
Team
CSU Fullerton, Team 2-5, Bruce Fall 2016
Member of CSU Fullerton, Team 2-5, Bruce Fall 2016
CSUF-BRUCE-F16S2G5
4 Members
4 Guides authored
