Insignia Ns B4111 Motherboard Replacement Repair Guide

Difficulty

Difficult

Steps

Time Required

                          30 minutes

Sections

Battery
2 steps
Casing
2 steps
Antenna Base
1 step
Motherboard
4 steps
Motherboard
2 steps

Flags

BackInsignia NS-B4111
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Unplug and remove the power cord. Turn the boombox upside down.
Grip the sides of the case and use your thumbs to pop open the battery cover.

Unplug and remove the power cord. Turn the boombox upside down.

Grip the sides of the case and use your thumbs to pop open the battery cover.

1024

Step 2

Pry out the batteries with your fingers.

Pry out the batteries with your fingers.

Step 3

              Casing

Turn the boombox upside down again. With the Phillips PH1 or the Flathead #3 screwdriver, remove the three 14mm black screws.
Remove the four 18mm chrome screws with the Phillips PH1 screwdriver.

Turn the boombox upside down again. With the Phillips PH1 or the Flathead #3 screwdriver, remove the three 14mm black screws.

Remove the four 18mm chrome screws with the Phillips PH1 screwdriver.

Step 4

Gently remove the bottom half of the casing from the top half of the casing.
The antenna base is connected to the motherboard by a red wire. This wire will prevent the two halves from separating completely.

Gently remove the bottom half of the casing from the top half of the casing.

The antenna base is connected to the motherboard by a red wire. This wire will prevent the two halves from separating completely.

Step 5

              Antenna Base

Remove the 10mm chrome screw from the antenna base with the Phillips PH1 screwdriver. Remove the antenna base from the casing.
This red wire will now be loose and you can move it out of the antenna base slot.

Remove the 10mm chrome screw from the antenna base with the Phillips PH1 screwdriver. Remove the antenna base from the casing.

This red wire will now be loose and you can move it out of the antenna base slot.

Step 6

              Motherboard

Unscrew the four 12.5mm screws with the Phillips PH1 Screwdriver.
Unscrew the one 10mm long screw with the Phillips PH1 Screwdriver.

Unscrew the four 12.5mm screws with the Phillips PH1 Screwdriver.

Unscrew the one 10mm long screw with the Phillips PH1 Screwdriver.

Step 7

Orient the device so that the back is facing you.
Unplug the six pin male/female header from its socket on the motherboard. The wires on the header are these colors: burgundy, red, orange, yellow, green, and blue.
Use a tweezer if you find it hard to pull the header out with your fingers.
Gently pull out the ribbon cable from its socket on the motherboard.
Pay attention to the orientation of the header and the ribbon cable. Replacing the wires the wrong way may short circuit the board.

Orient the device so that the back is facing you.

Unplug the six pin male/female header from its socket on the motherboard. The wires on the header are these colors: burgundy, red, orange, yellow, green, and blue.

Use a tweezer if you find it hard to pull the header out with your fingers.

Gently pull out the ribbon cable from its socket on the motherboard.

Pay attention to the orientation of the header and the ribbon cable. Replacing the wires the wrong way may short circuit the board.

Step 8

Rotate the device so that the front is facing you.
Unplug the four pin header from its socket on the motherboard. The wires on the header are these colors: brown, red, orange, and yellow.
Use a tweezer if you find it hard to pull this header out with your fingers.
Gently pull out the ribbon cable from its socket.
Pay attention to the orientation of the header and the ribbon cable. Replacing the base the wrong way may short circuit the board.

Rotate the device so that the front is facing you.

Unplug the four pin header from its socket on the motherboard. The wires on the header are these colors: brown, red, orange, and yellow.

Use a tweezer if you find it hard to pull this header out with your fingers.

Gently pull out the ribbon cable from its socket.

Pay attention to the orientation of the header and the ribbon cable. Replacing the base the wrong way may short circuit the board.

Step 9

Pull out the two pin header from its socket on the motherboard. The wires on this header are black and white.
Use a tweezer if you find it hard to pull this cable out with your fingers.

Pull out the two pin header from its socket on the motherboard. The wires on this header are black and white.

Use a tweezer if you find it hard to pull this cable out with your fingers.

Step 10

              Motherboard

Scrape off the glue from the black wire with the blue plastic opening tool.

Scrape off the glue from the black wire with the blue plastic opening tool.

Step 11

Desolder the one black, one red, and two blue wires. If you need help soldering, see this guide.

Desolder the one black, one red, and two blue wires. If you need help soldering, see this guide.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 4 other contributors

                    Kristin Yoshioka

Member since: 09/21/2016

984 Reputation

                                      9 Guides authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       UC Davis, Team 1-5, Oliver Fall 2016                        

                                                  Member of UC Davis, Team 1-5, Oliver Fall 2016 



                    UCD-OLIVER-F16S1G5                     


                                            5 Members                     


                                            11 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team