Difficulty

Moderate

Steps

18

Time Required

Suggest a time??

Sections

1

  • Screen
  • 18 steps

Flags

4

Markup Mishap

This guide needs better markups. Help out by correcting or making some markup annotations.

Step Trimmer

This guide has unnecessary steps. Trim them to be more concise!

Better Introduction

Improve this guide by completing or revising its introduction.

Missing Details

Some of this guide’s details are missing. Help users by adding tools, difficulty, or time.

  • BackInsignia Flex 8 NS-P08A7100

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

What you need

Step 1

              Screen
  • Begin by using the opening tool to pry open the back cover. Continue around the edge until the back cover pops off.

Begin by using the opening tool to pry open the back cover. Continue around the edge until the back cover pops off.

1024

Step 2

  • Use the opening tool to flip the LCD flex circuit plug upwards. The flex circuit should now be loose. Remove flex circuit by pulling outwards.

Use the opening tool to flip the LCD flex circuit plug upwards. The flex circuit should now be loose. Remove flex circuit by pulling outwards.

Step 3

  • Use the opening tool to remove the battery cable from the circuit board.

Use the opening tool to remove the battery cable from the circuit board.

Step 4

  • Remove the adhesive tape from the bottom of the battery.

Remove the adhesive tape from the bottom of the battery.

Step 5

  • Remove plastic adhesive tape from the side of the battery.

Remove plastic adhesive tape from the side of the battery.

Step 6

  • Pry the battery from the back of the LCD screen using the opening tool. Due to the strong adhesive between the battery and screen, this may take some time.

Pry the battery from the back of the LCD screen using the opening tool. Due to the strong adhesive between the battery and screen, this may take some time.

Step 7

  • Begin removing the screws on the circuit board using the phillips-head bit driver. Start with the top left corner.

Begin removing the screws on the circuit board using the phillips-head bit driver. Start with the top left corner.

Step 8

  • Remove the next screw to the right using the phillips-head bit driver.

Remove the next screw to the right using the phillips-head bit driver.

Step 9

  • Remove the next screw to the right using the phillips-head bit driver. This one is slightly hidden under the flex circuit of the camera.

Remove the next screw to the right using the phillips-head bit driver. This one is slightly hidden under the flex circuit of the camera.

Step 10

  • Remove the next screw in the right top right using the phillips-head bit driver.

Remove the next screw in the right top right using the phillips-head bit driver.

Step 11

  • Remove the next screw in the bottomeright corner using the phillips-head bit driver.

Remove the next screw in the bottomeright corner using the phillips-head bit driver.

Step 12

  • Remove the next screw in the bottom left corner using the phillips-head bit driver.

Remove the next screw in the bottom left corner using the phillips-head bit driver.

Step 13

  • Remove the flex circuit on the left side of the circuit board using the opening tool.

Remove the flex circuit on the left side of the circuit board using the opening tool.

Step 14

  • Remove the speaker cable from the circuit board using the opening tool.

Remove the speaker cable from the circuit board using the opening tool.

Step 15

  • Remove the camera cable from the circuit board using the opening tool.

Remove the camera cable from the circuit board using the opening tool.

Step 16

  • Flip the camera flex circuit clip upwards using the opening tool. Detach the camera flex circuit from the circuit board

Flip the camera flex circuit clip upwards using the opening tool. Detach the camera flex circuit from the circuit board

Step 17

  • Remove the adhesive tape holding the circuit board to the LCD screen. The circuit should now be free.

Remove the adhesive tape holding the circuit board to the LCD screen. The circuit should now be free.

Step 18

  • Pull the circuit board forward for clearance and begin removing the screen with the opening tool.

Pull the circuit board forward for clearance and begin removing the screen with the opening tool.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 1 other contributor 


                    Marco Soto

Member since: 07/08/2019

347 Reputation

                                      1 Guide authored                  



                       Badges:
                       5







                                                        +2 more badges

Team

                       IUPUI, Team S1-G1, Renguette Summer 2019                        

                                                  Member of IUPUI, Team S1-G1, Renguette Summer 2019 



                    IUPUI-RENGUETTE-SU19S1G1                     


                                            3 Members                     


                                            2 Guides authored