Insignia Flex 11 6 Screen Replacement Repair Guide

Difficulty

Moderate

Steps

15

Time Required

                          20 - 50 minutes            

Sections

3

• Power Removal
• 4 steps
• Motherboard
• 6 steps
• Screen
• 5 steps

Flags

0

• BackInsignia Flex 11.6

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Power Removal               

• Before working on the device, make sure the device is off and not plugged into any power source for safety reasons. Failure to comply could result in injury.
• Place the device on a firm surface with the device screen facing down.

Before working on the device, make sure the device is off and not plugged into any power source for safety reasons. Failure to comply could result in injury.

Place the device on a firm surface with the device screen facing down.

1024

Step 2

• Remove 2, 6.1 mm Phillips J000 screws from the back of the device.
• If any screws are stripped, refer to the ifixit guide for how to remove a stripped screw. How to Remove a Stripped Screw

Remove 2, 6.1 mm Phillips J000 screws from the back of the device.

If any screws are stripped, refer to the ifixit guide for how to remove a stripped screw. How to Remove a Stripped Screw

Step 3

• Using a plastic tool and the plastic card, gently pry off the back cover.

Using a plastic tool and the plastic card, gently pry off the back cover.

Step 4

• Using tweezers, remove the electrical connector that connects to the battery to remove the power to the battery.

Using tweezers, remove the electrical connector that connects to the battery to remove the power to the battery.

Step 5

              Motherboard               

• Unplug the 2 speaker’s connection from the motherboard.

Unplug the 2 speaker’s connection from the motherboard.

Step 6

• Peel the yellow tape off from on top of the electrical connectors.

Peel the yellow tape off from on top of the electrical connectors.

Step 7

• Flip up the black cover pieces to expose the 3 electrical connectors.
• Remove 3 electrical connectors by gently pulling back on them with some tweezers.

Flip up the black cover pieces to expose the 3 electrical connectors.

Remove 3 electrical connectors by gently pulling back on them with some tweezers.

Step 8

• Unplug the 2 black ground wires from the motherboard by gently prying on them until they unhook from the motherboard.
• Remove the black camera connector by gently prying on it until it unhooks.

Unplug the 2 black ground wires from the motherboard by gently prying on them until they unhook from the motherboard.

Remove the black camera connector by gently prying on it until it unhooks.

Step 9

• Using tweezers, remove the microphone from the the plastic cover.

Using tweezers, remove the microphone from the the plastic cover.

Step 10

• Remove 5 - 3.4 mm Phillips J000 screws from the motherboard.
• Motherboard pops out.

Remove 5 - 3.4 mm Phillips J000 screws from the motherboard.

Motherboard pops out.

Step 11

              Screen               

• Remove battery by prying off with card.

Remove battery by prying off with card.

Step 12

• Peel back the copper color electrical connector with blue opening tool.

Peel back the copper color electrical connector with blue opening tool.

Step 13

• Remove 12 - 4.15mm J000 Phillips screws from the metal bracket.
• Bracket will then come off.

Remove 12 - 4.15mm J000 Phillips screws from the metal bracket.

Bracket will then come off.

Step 14

• Remove 1 - 3.4 mm J000 Phillips screw from metal plate bracket.

Remove 1 - 3.4 mm J000 Phillips screw from metal plate bracket.

Step 15

• Remove screen from case by prying with a card.

Remove screen from case by prying with a card.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.                                             

Author

                                      with 4 other contributors 

                    Connor Sweeney                     

Member since: 09/28/2016

422 Reputation

                                      5 Guides authored                  



                       Badges:
                       16







                                                        +13 more badges                           

Team

                       Eastern Washington University, Team 2-4, Mathisen Fall 2016                        

                                                  Member of Eastern Washington University, Team 2-4, Mathisen Fall 2016 



                    EWU-MATHISEN-F16S2G4                     


                                            4 Members                     


                                            10 Guides authored                     

Charles Kinnison - Apr 12, 2017

Reply

The Flex 11.6" Model# NS-P11W7100 DOEST HAVE THOSE SCREWS RIGHT THERE!!!!!

Joshua Francis - May 22, 2018

yeah, thats the one I have. its quite a bit different. the speaker wires are soldered, too…

Joshua Francis - May 22, 2018

Reply

mine doesn’t look like that…

florence sefaa - Dec 23, 2020

Reply

where can i get a new screen to buy?

Do you sell the insignia ns-p11w7100 tablet 11.6 inches screen? I need on to fix my broken part.