Insignia Flex 10 1 Ns P10A6100 Screen Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          20 - 30 minutes

Sections

Back Case
3 steps
Camera
3 steps
Screen
13 steps

Flags

BackInsignia Flex 10.1 NS-P10A6100
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Back Case

Make sure your tablet is turned off and not connected to a power source to prevent personal injury.
The volume rocker and power button located on the top edge by the camera are not connected pieces and will become free from the device once the front panel is removed from the back case. They are easily put back in place when reassembling the tablet.
Position the tablet with the top edge by the camera facing down.
Insert the plastic opening tool between the front panel and back case at the upper left hand corner of the tablet.

Make sure your tablet is turned off and not connected to a power source to prevent personal injury.

The volume rocker and power button located on the top edge by the camera are not connected pieces and will become free from the device once the front panel is removed from the back case. They are easily put back in place when reassembling the tablet.

Position the tablet with the top edge by the camera facing down.

Insert the plastic opening tool between the front panel and back case at the upper left hand corner of the tablet.

1024

Step 2

Slide the plastic opening tool along the edge of the tablet between the front panel and back case.
Repeat this process for the two shorter edges of the tablet leaving the top edge by the camera still snapped in place.

Slide the plastic opening tool along the edge of the tablet between the front panel and back case.

Repeat this process for the two shorter edges of the tablet leaving the top edge by the camera still snapped in place.

Step 3

Using an unfolding motion along the top edge of the tablet, carefully separate the front panel from the back case.

Using an unfolding motion along the top edge of the tablet, carefully separate the front panel from the back case.

Step 4

              Camera

Using the Phillips #000 screw driver, unscrew the two 4 mm screws securing the camera to the front panel in a counterclockwise direction.
The two screws are very small, so be careful not to lose them after unscrewing them.

Using the Phillips #000 screw driver, unscrew the two 4 mm screws securing the camera to the front panel in a counterclockwise direction.

The two screws are very small, so be careful not to lose them after unscrewing them.

Step 5

Using the plastic opening tool, lift up the black retaining flap that secures the camera ZIF (zero insertion force) ribbon connector to the motherboard.

Using the plastic opening tool, lift up the black retaining flap that secures the camera ZIF (zero insertion force) ribbon connector to the motherboard.

Step 6

Pull the camera ZIF (zero insertion force) ribbon connector out from underneath the black retaining flap.
Remove the camera.

Pull the camera ZIF (zero insertion force) ribbon connector out from underneath the black retaining flap.

Remove the camera.

Step 7

              Screen

Using the Phillips #000 screw driver, unscrew the four 4 mm screws securing the four gray clasps to the front panel in a counterclockwise direction.
The four screws are very small, so be careful not to lose them after unscrewing them.

Using the Phillips #000 screw driver, unscrew the four 4 mm screws securing the four gray clasps to the front panel in a counterclockwise direction.

The four screws are very small, so be careful not to lose them after unscrewing them.

Step 8

Using the plastic opening tool, pry the four gray clips from the front panel.
The gray clips rest lightly in place on the front panel, so minimal force is required to remove and place them.

Using the plastic opening tool, pry the four gray clips from the front panel.

The gray clips rest lightly in place on the front panel, so minimal force is required to remove and place them.

Step 9

Using the Phillips #000 screw driver, unscrew the four 4 mm screws securing the speakers to the front panel in a counterclockwise direction.
The four screws are very small, so be careful not to lose them after unscrewing them.

Using the Phillips #000 screw driver, unscrew the four 4 mm screws securing the speakers to the front panel in a counterclockwise direction.

Step 10

Using the Phillips #000 screw driver, unscrew the three 4 mm screws securing the motherboard to the front panel in a counterclockwise direction.
The three screws are very small, so be careful not to lose them after unscrewing them.

Using the Phillips #000 screw driver, unscrew the three 4 mm screws securing the motherboard to the front panel in a counterclockwise direction.

The three screws are very small, so be careful not to lose them after unscrewing them.

Step 11

Using the plastic opening tool, lift up the black retaining flap that secures the volume and power button ZIF (zero insertion force) ribbon connector to the motherboard.

Using the plastic opening tool, lift up the black retaining flap that secures the volume and power button ZIF (zero insertion force) ribbon connector to the motherboard.

Step 12

Pull the ZIF (zero insertion force) ribbon connector out from underneath the black retaining flap.

Pull the ZIF (zero insertion force) ribbon connector out from underneath the black retaining flap.

Step 13

Using the plastic opening tool, remove the silver tape covering the display ZIF (zero insertion force) ribbon connector.

Using the plastic opening tool, remove the silver tape covering the display ZIF (zero insertion force) ribbon connector.

Step 14

Using the plastic opening tool, lift up the black retaining flap that secures the display ZIF (zero insertion force) ribbon connector to the motherboard.

Using the plastic opening tool, lift up the black retaining flap that secures the display ZIF (zero insertion force) ribbon connector to the motherboard.

Step 15

Step 16

Position the tablet with the top edge by the cameras facing up.
Insert the heavy-duty spudger at the top right corner.

Position the tablet with the top edge by the cameras facing up.

Insert the heavy-duty spudger at the top right corner.

Step 17

Lift the screen from the front panel with a prying motion to detach it from the clips holding it in place.

Lift the screen from the front panel with a prying motion to detach it from the clips holding it in place.

Step 18

Pop the screen out from the front panel.
Be careful not to bend the front panel too much as it might break.

Pop the screen out from the front panel.

Be careful not to bend the front panel too much as it might break.

Step 19

Lift the screen from the front panel to remove.

Lift the screen from the front panel to remove.

The screen is now free from the device and can be replaced. To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.

Author

                                      with 1 other contributor

                    Samantha Damewood

Member since: 10/29/2016

961 Reputation

                                      5 Guides authored                  



                       Badges:
                       15







                                                        +12 more badges

Team

                       Baylor, Team 5-8, Williams Fall 2016                        

                                                  Member of Baylor, Team 5-8, Williams Fall 2016 



                    BU-WILLIAMS-F16S5G8                     


                                            3 Members                     


                                            12 Guides authored

dcutler01 - May 26, 2017

Do you have a guide for replacing the lcd screen?

Gerardo Lerma - Mar 21, 2020

Whic screen models works wirt this tablet?

Introduction#

What you need#

Team#

Introduction

What you need

Team