Difficulty

Moderate

Steps

6

Time Required

                          20 minutes

Sections

2

  • Top Panel
  • 5 steps
  • Lens
  • 1 step

Flags

1

This guide has been the hard work of our awesome students and is found to be exceptionally cool by the iFixit staff.

  • BackInFocus Screenplay 4805

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

You will need a replacement lens as well as a clean, micro fabric cloth in case the replacement lens needs to be cleaned.

What you need

Step 1

              Top Panel
  • Flip the projector on its back.
  • Use the Phillips #2 screwdriver to remove the (4) four 2 cm gold screws.
  • Use the Phillips #2 screwdriver to remove the (3) three 1 cm silver screws.

Flip the projector on its back.

Use the Phillips #2 screwdriver to remove the (4) four 2 cm gold screws.

Use the Phillips #2 screwdriver to remove the (3) three 1 cm silver screws.

1024

Step 2

  • Turn the projector, facing the back cable board towards you.
  • Using the Phillips #0 screwdriver, remove the (3) three 1.0 cm silver screws on the back panel.
  • Gently take off back cable panel.

Turn the projector, facing the back cable board towards you.

Using the Phillips #0 screwdriver, remove the (3) three 1.0 cm silver screws on the back panel.

Gently take off back cable panel.

Step 3

  • Turn the projector so the front side with the lens is facing you.
  • Gently pry the both of the grey lens rings using the metal spudger.

Turn the projector so the front side with the lens is facing you.

Gently pry the both of the grey lens rings using the metal spudger.

Step 4

  • Now that the screws have been removed, proceed with the removal of the outer panel.
  • Gently remove the front lens panel.
  • Be forewarned, the panel will resist. Be careful not to break the lens.

Now that the screws have been removed, proceed with the removal of the outer panel.

Gently remove the front lens panel.

Be forewarned, the panel will resist. Be careful not to break the lens.

Step 5

  • Being careful not to pull the wires inside the projector, gently lift the top panel off the projector.
  • Rest the lid behind the projector so the insides are exposed and undamaged.

Being careful not to pull the wires inside the projector, gently lift the top panel off the projector.

Rest the lid behind the projector so the insides are exposed and undamaged.

Step 6

              Lens
  • Using the Phillips #1 screwdriver, remove the (3) three 1cm black screws on the face of the lens.
  • Gently pull out the lens.

Using the Phillips #1 screwdriver, remove the (3) three 1cm black screws on the face of the lens.

Gently pull out the lens.

To reassemble the device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 3 other contributors 


                    Marilyn Urness

Member since: 09/28/2017

671 Reputation

                                      6 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       Eastern Washington University, Team S2-G3, Crane Fall 2017                        

                                                  Member of Eastern Washington University, Team S2-G3, Crane Fall 2017 



                    EWU-CRANE-F17S2G3                     


                                            5 Members                     


                                            6 Guides authored