Difficulty
Moderate
Steps
8
Time Required
15 - 20 minutes
Sections
2
- Main Board
- 6 steps
- Lens
- 2 steps
Flags
1
Better Introduction
Improve this guide by completing or revising its introduction.
BackInFocus LP540
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
What you need
Step 1
Main Board
- Flip the projector right-side up and turn it so that the back ports are facing you.
- Remove the 7 mm metallic screws using the flat-head screwdriver.
- Using the T10 Torx screwdriver, remove the two black 10 mm screws located at the center of the back panel.
Flip the projector right-side up and turn it so that the back ports are facing you.
Remove the 7 mm metallic screws using the flat-head screwdriver.
Using the T10 Torx screwdriver, remove the two black 10 mm screws located at the center of the back panel.
1024
Step 2
- Flip the projector over.
- Use the T10 Torx screwdriver head to remove the two 77mm screws located nearest to the back panel ports.
- Remove the two 10mm screws located near the lens side with the T10 Torx screwdriver head.
- Flip the projector back over.
- Lift up the main lid cautiously to avoid ripping the electrical ribbons.
Flip the projector over.
Use the T10 Torx screwdriver head to remove the two 77mm screws located nearest to the back panel ports.
Remove the two 10mm screws located near the lens side with the T10 Torx screwdriver head.
Flip the projector back over.
Lift up the main lid cautiously to avoid ripping the electrical ribbons.
Step 3
- Unplug the speaker wire from the circuit board by simultaneously squeezing the sides and pulling.
- Pull on the brown tabs located at the sides of the white plastic ribbon holder and pull the ribbon out.
- Remove the top cover.
Unplug the speaker wire from the circuit board by simultaneously squeezing the sides and pulling.
Pull on the brown tabs located at the sides of the white plastic ribbon holder and pull the ribbon out.
Remove the top cover.
Step 4
- Hold down the release tabs to remove the cables from the white tabs.
Hold down the release tabs to remove the cables from the white tabs.
Step 5
- Use the T10 Torx screwdriver to remove the five 5mm screws located throughout the motherboard.
- Pull up the five metal tabs located at the rear of the projector.
- Do not pull up on the metal tabs too hard or too fast because they can break easily.
Use the T10 Torx screwdriver to remove the five 5mm screws located throughout the motherboard.
Pull up the five metal tabs located at the rear of the projector.
Do not pull up on the metal tabs too hard or too fast because they can break easily.
Step 6
- Remove the three gold ribbons by flipping up the black taps that hold the ribbon in place.
- Pull the ribbons out carefully and place them under the main board.
- Carefully lift the entire main board up.
Remove the three gold ribbons by flipping up the black taps that hold the ribbon in place.
Pull the ribbons out carefully and place them under the main board.
Carefully lift the entire main board up.
Step 7
Lens
- Remove the two 10 mm screws using the Philips 0 screwdriver head.
Remove the two 10 mm screws using the Philips 0 screwdriver head.
Step 8
- Carefully hold the lens from both ends and lift up simultaneously
Carefully hold the lens from both ends and lift up simultaneously
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 6 other contributors
Jorge L Navarro
Member since: 01/22/2014
533 Reputation
5 Guides authored
Badges:
7
+4 more badges
Team
Cal Poly, Team 13-17, Regan Winter 2014
Member of Cal Poly, Team 13-17, Regan Winter 2014
CPSU-REGAN-W14S13G17
6 Members
5 Guides authored
