Difficulty

Moderate

Steps

9

Time Required

                          10 minutes

Sections

2

  • Top Plate
  • 2 steps
  • Lamp
  • 7 steps

Flags

Needs More Images

A few more images would make this guide’s procedures crystal clear.

Missed a Step

Oops! This guide is currently missing some important steps.

  • BackInFocus IN3114

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Top Plate
  • Use a Phillips #1 screwdriver to remove the 1.2 cm Phillips-head screw from each side of the projector.

Use a Phillips #1 screwdriver to remove the 1.2 cm Phillips-head screw from each side of the projector.

1024

Step 2

  • Use your hands to slide the top plate off of the projector.
  • Lift and remove the plate.

Use your hands to slide the top plate off of the projector.

Lift and remove the plate.

Step 3

              Lamp
  • Use a Phillips #1 screwdriver to unscrew the two 9 mm screws on the top of the lamp housing unit.
  • Screws will not come all the way out. It is best to just loosen them as much as possible.

Use a Phillips #1 screwdriver to unscrew the two 9 mm screws on the top of the lamp housing unit.

Screws will not come all the way out. It is best to just loosen them as much as possible.

Step 4

  • Use your hands to pull up on the silver handle and remove the lamp housing unit.

Use your hands to pull up on the silver handle and remove the lamp housing unit.

Step 5

  • Once the lamp housing is removed flip it over where silver pull tab is face down.
  • Use a Phillips #00 screwdriver to remove the 5 mm screw from the right side of the lamp housing unit.
  • Use a Phillips #00 screwdriver to remove the two 5 mm screws from the top of the unit.

Once the lamp housing is removed flip it over where silver pull tab is face down.

Use a Phillips #00 screwdriver to remove the 5 mm screw from the right side of the lamp housing unit.

Use a Phillips #00 screwdriver to remove the two 5 mm screws from the top of the unit.

Step 6

  • Use hands to pull off the black unit cover.

Use hands to pull off the black unit cover.

Step 7

  • Once the cover is removed, flip the housing unit so the bulb is face down.
  • Remove the four 4 mm screws with a Phillips #00 screwdriver.

Once the cover is removed, flip the housing unit so the bulb is face down.

Remove the four 4 mm screws with a Phillips #00 screwdriver.

Step 8

  • Use hands to pull out the bulb and silver cover.
  • Gently pull on the two wires that connect the bulb to its housing to disconnect them.

Use hands to pull out the bulb and silver cover.

Gently pull on the two wires that connect the bulb to its housing to disconnect them.

Step 9

  • Once wires are disconnected, Remove the bulb from the silver cover and replace.

Once wires are disconnected, Remove the bulb from the silver cover and replace.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors 


                    Lily Calvert

Member since: 03/21/2022

145 Reputation

                                      1 Guide authored                  



                       Badges:
                       2

Team

                       University of Alabama, Team 3-3, Bedsole Spring 2022                        

                                                  Member of University of Alabama, Team 3-3, Bedsole Spring 2022 



                    UA-BEDSOLE-S22S3G3                     


                                            4 Members                     


                                            4 Guides authored