Difficulty

Moderate

Steps

6

Time Required

                          5 minutes

Sections

3

  • Top Cover
  • 2 steps
  • InFocus IN3104 Metal Cover Disassembly
  • 2 steps
  • Cooling Fan
  • 2 steps

Flags

0

  • BackInFocus IN3104

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Top Cover
  • Turn the projector so that the lens is facing you.
  • On the left side of the projector, there is a screw and a knob inside of the small grate.
  • Use a Phillips #1 screwdriver to remove the 6 mm screw that secures top cover.
  • Remove the service cover.

Turn the projector so that the lens is facing you.

On the left side of the projector, there is a screw and a knob inside of the small grate.

Use a Phillips #1 screwdriver to remove the 6 mm screw that secures top cover.

Remove the service cover.

1024

Step 2

  • Use a Phillips #1 screwdriver to remove the seven 6 mm screws.
  • Use a Phillips #1 screwdriver to remove the two 5 mm screws.
  • Remove the top cover.
  • Do not pull the cover too hard. It may damage the wire that is connected to the motherboard.

Use a Phillips #1 screwdriver to remove the seven 6 mm screws.

Use a Phillips #1 screwdriver to remove the two 5 mm screws.

Remove the top cover.

Do not pull the cover too hard. It may damage the wire that is connected to the motherboard.

Step 3

              InFocus IN3104 Metal Cover Disassembly
  • Use a Phillips #1 screwdriver to remove the nine 6 mm screws.
  • Lift up the metal cover and set it aside to reveal the motherboard.

Use a Phillips #1 screwdriver to remove the nine 6 mm screws.

Lift up the metal cover and set it aside to reveal the motherboard.

Step 4

  • Carefully pry up the black plastic locking bar of the ZIF connector on the motherboard with a plastic spudger.
  • Pull out the blue-tipped, white ribbon cable from the connector.
  • Remove the metal cover.

Carefully pry up the black plastic locking bar of the ZIF connector on the motherboard with a plastic spudger.

Pull out the blue-tipped, white ribbon cable from the connector.

Remove the metal cover.

Step 5

              Cooling Fan
  • Use a Phillips #1 screwdriver to remove the three 6 mm screws on the metal cover beside the lamp.
  • The screws are in a tight location, so you may need a thin screwdriver or an extension to remove them.

Use a Phillips #1 screwdriver to remove the three 6 mm screws on the metal cover beside the lamp.

The screws are in a tight location, so you may need a thin screwdriver or an extension to remove them.

Step 6

  • Unplug the yellow, red, and black colored cable bundle from the motherboard.
  • Remove the cooling fan from the device by lifting it out.

Unplug the yellow, red, and black colored cable bundle from the motherboard.

Remove the cooling fan from the device by lifting it out.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 4 other contributors 


                    Tae Min Kim

Member since: 01/24/2020

409 Reputation

                                      5 Guides authored                  



                       Badges:
                       6







                                                        +3 more badges

Team

                       Embry-Riddle Aeronautical University, Team S5-G5, Watkins Spring 2020                        

                                                  Member of Embry-Riddle Aeronautical University, Team S5-G5, Watkins Spring 2020 



                    ERAU-WATKINS-S20S5G5                     


                                            4 Members                     


                                            7 Guides authored