Infant Optics Dxr 5 Monitor Screen Replacement Repair Guide

Difficulty

Moderate

Steps

10

Time Required

                          10 minutes            

Sections

2

• Battery
• 4 steps
• Monitor Screen
• 6 steps

Flags

Action Shots

Be an action hero! This guide needs images that better demonstrate how to perform specific actions.

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

• BackInfant Optics DXR-5

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

Secure screws to avoid losing them.

Screws are small and can pose a possible choking hazard for small children.

What you need

Step 1

              Battery               

• Press on the blue clip on the back and slide it down.
• In the second picture there is a slight gap at the top of the blue clip.

Press on the blue clip on the back and slide it down.

In the second picture there is a slight gap at the top of the blue clip.

1024

Step 2

• Pull the blue clip away from the body of the hand held monitor.

Pull the blue clip away from the body of the hand held monitor.

Step 3

• Slide the rear white panel off as shown.

Slide the rear white panel off as shown.

Step 4

• Remove the battery by pushing in on the right side and then pulling the battery up and out of the body of the hand held monitor.

Remove the battery by pushing in on the right side and then pulling the battery up and out of the body of the hand held monitor.

Step 5

              Monitor Screen               

• Remove the four 6.0 mm Phillips screws located on the back of the hand held monitor using a Phillips #2 screwdriver.
• There are two types of screws. Be sure to return the screws to their respective holes upon reassembly.

Remove the four 6.0 mm Phillips screws located on the back of the hand held monitor using a Phillips #2 screwdriver.

There are two types of screws. Be sure to return the screws to their respective holes upon reassembly.

Step 6

• Carefully remove the clear face plate on the front of the hand held monitor using a plastic spudger and a suction cup.
• Use a heat source to loosen the adhesive around the edge of the face plate before applying any pressure to the face plate.

Carefully remove the clear face plate on the front of the hand held monitor using a plastic spudger and a suction cup.

Use a heat source to loosen the adhesive around the edge of the face plate before applying any pressure to the face plate.

Step 7

• Using a Phillips #2 screwdriver, remove the two 6.0 mm Phillips screws that are exposed after removing the face plate.

Using a Phillips #2 screwdriver, remove the two 6.0 mm Phillips screws that are exposed after removing the face plate.

Step 8

• Using a drill carefully drill out the plastic posts that connect the mother board to the face plate.

Using a drill carefully drill out the plastic posts that connect the mother board to the face plate.

Step 9

• Carefully open the hand held monitor and flip the screen (highlighted in red) out of the way.

Carefully open the hand held monitor and flip the screen (highlighted in red) out of the way.

Step 10

• Remove the hand held monitor screen from the mother board by carefully pulling from the point where it is attached with an adhesive to the mother board.

Remove the hand held monitor screen from the mother board by carefully pulling from the point where it is attached with an adhesive to the mother board.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.                                             

Author

                                      with 4 other contributors 

                    Charles Neal                     

Member since: 08/31/2015

687 Reputation

                                      5 Guides authored                  



                       Badges:
                       15







                                                        +12 more badges                           

Team

                       USF Tampa, Team 6-2, Remmell Fall 2015                        

                                                  Member of USF Tampa, Team 6-2, Remmell Fall 2015 



                    USFT-REMMELL-F15S6G2                     


                                            5 Members                     


                                            5 Guides authored                     

Abdullah - Apr 29, 2018

Reply

Any ideas on where to source the replacement screen?