Difficulty

Easy

Steps

22

Time Required

                          10 - 20 minutes

Sections

1

  • Impuls LED Alarm Clock Radio Disassembly
  • 22 steps

Flags

0

  • BackImpuls LED Alarm Clock Radio

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Impuls LED Alarm Clock Radio Disassembly
  • Unscrew the 4 base screws at the bottom with the Phillips 1 screwdriver.

Unscrew the 4 base screws at the bottom with the Phillips 1 screwdriver.

1024

Step 2

  • Open the top and remove the transparent plastic cap.

Open the top and remove the transparent plastic cap.

Step 3

  • Remove the 4 screws from the PCB.
  • It is desirable to use 3 hands because you have to do 3 jobs: screw, hold the top and hold the bottom.

Remove the 4 screws from the PCB.

It is desirable to use 3 hands because you have to do 3 jobs: screw, hold the top and hold the bottom.

Step 4

  • Remove/unclick 4 plastic buttons.
  • There are 4 different types of buttons.

Remove/unclick 4 plastic buttons.

There are 4 different types of buttons.

Step 5

  • Unscrew 2 screws of the radio tuning system.

Unscrew 2 screws of the radio tuning system.

Step 6

  • Remove the gear that protects the cap.

Remove the gear that protects the cap.

Step 7

  • Lift up the small gear.

Lift up the small gear.

Step 8

  • Lift up the flexible pin rack.

Lift up the flexible pin rack.

Step 9

  • Remove the flexible pin rack holder.

Remove the flexible pin rack holder.

Step 10

  • Remove 3 screws of the big PCB.

Remove 3 screws of the big PCB.

Step 11

  • Remove the backside of the casing.

Remove the backside of the casing.

Step 12

  • Remove the grey double gear.

Remove the grey double gear.

Step 13

  • Remove the switch casing.

Remove the switch casing.

Step 14

  • Flip the big PCB.

Flip the big PCB.

Step 15

  • Unscrew 2 screws on the back of the PCB the black gear house.

Unscrew 2 screws on the back of the PCB the black gear house.

Step 16

  • Remove the black gear housing.

Remove the black gear housing.

Step 17

  • Unscrew 2 screws of the electro magnet.

Unscrew 2 screws of the electro magnet.

Step 18

  • Lift up the electro magnet.

Lift up the electro magnet.

Step 19

  • Unscrew the cap of the POT meter.

Unscrew the cap of the POT meter.

Step 20

  • Remove the big black double gear.

Remove the big black double gear.

Step 21

  • Remove the hot glue of the antenna.

Remove the hot glue of the antenna.

Step 22

  • Remove all the electrical components by desoldering.

Remove all the electrical components by desoldering.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 1 other contributor 


                    Pascalle van Hemert

Member since: 03/07/2018

325 Reputation

                                      1 Guide authored                  



                       Badges:
                       3

Team

                       Delft University of Technology, Team S1-G5, Flipsen Winter 2018                        

                                                  Member of Delft University of Technology, Team S1-G5, Flipsen Winter 2018 



                    TUD-FLIPSEN-W18S1G5                     


                                            5 Members                     


                                            1 Guide authored