Difficulty
Difficult
Steps
8
Time Required
30 - 45 minutes
Sections
1
- Electronic wire
- 8 steps
Flags
0
BackBlender
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Electronic wire
- Here you see the Impuls blender
- First, seperate the the blender jar from the bottom part by turning it and put it aside.
Here you see the Impuls blender
First, seperate the the blender jar from the bottom part by turning it and put it aside.
1024
Step 2
- Turn the bottom part over and look at the bottom.
- Take the rubber parts out of the 4 holes to reveal the screws.
- Take the 4 screws out using a Phillips screwdriver.
Turn the bottom part over and look at the bottom.
Take the rubber parts out of the 4 holes to reveal the screws.
Take the 4 screws out using a Phillips screwdriver.
Step 3
- Take the blue bottom part off the rest of the product to reveal the inside.
- Unscrew the black piece to be able to slide the blue part away from the rest.
Take the blue bottom part off the rest of the product to reveal the inside.
Unscrew the black piece to be able to slide the blue part away from the rest.
Step 4
- When you look to the inside, you see that there are two components; the buttons and the motor.
- Unscrew the part that contains the buttons and take it off.
When you look to the inside, you see that there are two components; the buttons and the motor.
Unscrew the part that contains the buttons and take it off.
Step 5
- Take out the 3 screws that are deep inside.
- Take off the blue part on top that was fixed with those screws.
- Pull the black disc out by using the screwdriver as lever from multiple sides.
- This will take some force, so do not be afraid it will break.
Take out the 3 screws that are deep inside.
Take off the blue part on top that was fixed with those screws.
Pull the black disc out by using the screwdriver as lever from multiple sides.
This will take some force, so do not be afraid it will break.
Step 6
- When you have taken off the black piece and revealed the 4 screws, unscrew them all.
- Take out the motor part and the rest of the electronics.
When you have taken off the black piece and revealed the 4 screws, unscrew them all.
Take out the motor part and the rest of the electronics.
Step 7
- Find the fraction in the wire.
- Cut off the broken part
- Strip both sides of the wire that have to be attached again.
Find the fraction in the wire.
Cut off the broken part
Strip both sides of the wire that have to be attached again.
Step 8
- If you will use a shrink sleeve to cover the electronic wire, it has to be put on the wire first. Otherwise if electrical tape is used, this can be done afterwards.
- Solder the two wires with a soldering iron.
- Shrink the sleeve with a heater or put the electrical tape around the soldered wire.
If you will use a shrink sleeve to cover the electronic wire, it has to be put on the wire first. Otherwise if electrical tape is used, this can be done afterwards.
Solder the two wires with a soldering iron.
Shrink the sleeve with a heater or put the electrical tape around the soldered wire.
To reassemble your device, follow the instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 3 other contributors
Daan van der Sande
Member since: 03/08/2017
101 Reputation
1 Guide authored
Badges:
3
Team
Delft University of Technology, Team S1-G10, Flipsen Spring 2017
Member of Delft University of Technology, Team S1-G10, Flipsen Spring 2017
TUD-FLIPSEN-S17S1G10
3 Members
1 Guide authored
