Difficulty

Moderate

Steps

13

Time Required

Suggest a time??

Sections

4

  • Access Door
  • 2 steps
  • Front Bezel
  • 7 steps
  • Camera Board
  • 3 steps
  • Microphone
  • 1 step

Flags

0

  • BackiMac G5 17" Model A1144

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Access Door
  • Before you work on the computer, unplug the computer and press the power button for 20-30 seconds to drain the stored energy in the power supply.
  • Loosen the two Phillips screws securing the access door to your iMac.
  • These screws are captive in the access door.

Before you work on the computer, unplug the computer and press the power button for 20-30 seconds to drain the stored energy in the power supply.

Loosen the two Phillips screws securing the access door to your iMac.

These screws are captive in the access door.

1024

Step 2

  • Remove the access door from your iMac.

Remove the access door from your iMac.

Step 3

              Front Bezel
  • Remove the three T8 Torx screws securing the front bezel to the rear panel.

Remove the three T8 Torx screws securing the front bezel to the rear panel.

Step 4

  • Orient the iMac face-up, on its backside.
  • Use your thumbs to press both RAM arms in past the front bezel for enough clearance to lift it off the rear case.

Orient the iMac face-up, on its backside.

Use your thumbs to press both RAM arms in past the front bezel for enough clearance to lift it off the rear case.

Step 5

  • While holding the RAM arms in with your thumbs, lift the lower edge of the front bezel enough to clear the rear case.

While holding the RAM arms in with your thumbs, lift the lower edge of the front bezel enough to clear the rear case.

Step 6

  • Re-orient your iMac so it sits upright on the stand.
  • Insert a plastic card up into the corner of the air vent slot at the top of the rear case.
  • Push the card toward the top of the iMac to release the front bezel latch.
  • Pull the front bezel away from the rear case.
  • Repeat this process for the other side of the front bezel.
  • It may be necessary to apply several layers of duct tape to the top of the access card to aid in releasing the latches.
  • If the bezel refuses to release, try pressing the lower edge back onto the rear case and repeat this opening process.

Re-orient your iMac so it sits upright on the stand.

Insert a plastic card up into the corner of the air vent slot at the top of the rear case.

Push the card toward the top of the iMac to release the front bezel latch.

Pull the front bezel away from the rear case.

Repeat this process for the other side of the front bezel.

It may be necessary to apply several layers of duct tape to the top of the access card to aid in releasing the latches.

If the bezel refuses to release, try pressing the lower edge back onto the rear case and repeat this opening process.

Step 7

  • Lay your iMac stand-side down on a table.
  • Lift the front bezel from its lower edge and rotate it away from the rest of your iMac, minding the RAM arms that may get caught.
  • Lay the front bezel above the rest of the iMac.

Lay your iMac stand-side down on a table.

Lift the front bezel from its lower edge and rotate it away from the rest of your iMac, minding the RAM arms that may get caught.

Lay the front bezel above the rest of the iMac.

Step 8

  • If necessary, remove the piece of kapton tape wrapped around the microphone and camera cables.

If necessary, remove the piece of kapton tape wrapped around the microphone and camera cables.

Step 9

  • Disconnect both the camera and microphone cables.

Disconnect both the camera and microphone cables.

Step 10

              Camera Board
  • Lay the bezel front side down on a table.
  • If necessary, peel back the tape covering the camera board.

Lay the bezel front side down on a table.

If necessary, peel back the tape covering the camera board.

Step 11

  • Remove the two T6 Torx screws securing the camera board to the front bezel.

Remove the two T6 Torx screws securing the camera board to the front bezel.

Step 12

  • Lift the camera board out from the front bezel.

Lift the camera board out from the front bezel.

Step 13

              Microphone
  • Use a spudger to pry the microphone off the adhesive holding it to the front bezel.

Use a spudger to pry the microphone off the adhesive holding it to the front bezel.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors 


                    Andrew Bookholt

575,478 Reputation

                                      618 Guides authored                  



                       Badges:
                       47







                                                        +44 more badges