Ilo 1Gb Mp3 Player External Volume Button And Hold Switch Replacement Repair Guide

Difficulty

Easy

Steps

9

Time Required

                          5 - 15 minutes            

Sections

3

• ilo Mp3 Player Battery and Case
• 3 steps
• ilo 1 Gb Mp3 Player Motherboard
• 4 steps
• External volume button and hold switch
• 2 steps

Flags

1

Inconsistent Images

Updating the images on this guide to be more consistent with the prerequisites would increase its awesomeness.

• Backilo 1Gb Mp3 Player

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Belt Clip               

• Remove the belt clip by pulling the clip casing up and away from the device starting at the top over the slightly protruding headphones jack.

Remove the belt clip by pulling the clip casing up and away from the device starting at the top over the slightly protruding headphones jack.

1024

Step 2

              Battery Cover               

• Remove the battery cover by gently pushing inward on the arrow on the cover.
• While maintaining pressure push the cover upward.

Remove the battery cover by gently pushing inward on the arrow on the cover.

While maintaining pressure push the cover upward.

Step 3

              Battery               

• Remove the Battery from the socket
• When installing the battery take note of the signs displayed in the socket to determine which direction the negative and positive ends should be.

Remove the Battery from the socket

When installing the battery take note of the signs displayed in the socket to determine which direction the negative and positive ends should be.

Step 4

              ilo 1 Gb Mp3 Player Motherboard               

• Under the cover you will find Three (3) 5mm screws that will need to be removed. For this you will need to use the PH00 screw tip included in your iFixit kit. Make sure to keep track of these screws as they will need to be reinserterd during the reassembly of your device.
• These screws are different from the two other screws from the interior

Under the cover you will find Three (3) 5mm screws that will need to be removed. For this you will need to use the PH00 screw tip included in your iFixit kit. Make sure to keep track of these screws as they will need to be reinserterd during the reassembly of your device.

These screws are different from the two other screws from the interior

Step 5

• Separate the front housing from the back housing using your thumbs. Carefully pry around the edge of the bottom of device then be sure to unhook the clip inside just below the hold switch.

Separate the front housing from the back housing using your thumbs. Carefully pry around the edge of the bottom of device then be sure to unhook the clip inside just below the hold switch.

Step 6

• Once you have removed the front housing and exposed the internal board and screen locate and Remove the Two (2) 4mm PH00 screws on the board.
• One is located in the top middle above the screen and the other is located at the bottom left between the Stop and Back buttons.

Once you have removed the front housing and exposed the internal board and screen locate and Remove the Two (2) 4mm PH00 screws on the board.

One is located in the top middle above the screen and the other is located at the bottom left between the Stop and Back buttons.

Step 7

• Once those screws are removed, gently remove the board from the rear casing.
• When installing the motherboard into the case be especially careful with the headphone and USB jacks located at the top of the motherboard. These should be slid into their sockets first.

Once those screws are removed, gently remove the board from the rear casing.

When installing the motherboard into the case be especially careful with the headphone and USB jacks located at the top of the motherboard. These should be slid into their sockets first.

Step 8

              Volume Rocker               

• Remove the Volume button from its rocker socket by gently pushing in on the button until it pops out if the two sockets.

Remove the Volume button from its rocker socket by gently pushing in on the button until it pops out if the two sockets.

Step 9

              Hold Switch               

• Remove Hold Switch from Socket by squeezing the prongs that hold the button in the socket together and push the button outward.

Remove Hold Switch from Socket by squeezing the prongs that hold the button in the socket together and push the button outward.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.                                             

Author

                                      with 3 other contributors 

                    Joe                     

Member since: 06/04/2013

291 Reputation

                                      2 Guides authored                  



                       Badges:
                       7







                                                        +4 more badges                           

Team

                       University of Kentucky Louisville, Team 1-3, Chamberlain Fall 2012                        

                                                  Member of University of Kentucky Louisville, Team 1-3, Chamberlain Fall 2012 



                    LOUISVILLE-CHAMBERLAIN-F12S1G3                     


                                            2 Members                     


                                            5 Guides authored