Ihome Ipl8 Screen Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          25 minutes

Sections

Battery
4 steps
Lightning Connector
5 steps
Screen
2 steps

Flags

BackiHome iPL8
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Turn the device over to access the bottom panel.
Locate the 6mm Phillips #2 screw under the label “unscrew to open door.”

Turn the device over to access the bottom panel.

Locate the 6mm Phillips #2 screw under the label “unscrew to open door.”

1024

Step 2

Using a Phillips #2 screwdriver, unscrew the captive screw.
Keep turning until the screw and the door are loose.

Using a Phillips #2 screwdriver, unscrew the captive screw.

Keep turning until the screw and the door are loose.

Step 3

Lift and remove the battery access panel.
The captive screw will remain attached to the panel.

Lift and remove the battery access panel.

The captive screw will remain attached to the panel.

Step 4

Gently press on the rim of the 3V battery.
Remove the 3V battery.

Gently press on the rim of the 3V battery.

Remove the 3V battery.

Step 5

              Lightning Connector

Keeping your device upside-down, locate the four 6mm Phillips #2 screws near each corner.
Remove the four 6mm Phillips #2 screws.

Keeping your device upside-down, locate the four 6mm Phillips #2 screws near each corner.

Remove the four 6mm Phillips #2 screws.

Step 6

Remove the four round pads from the bottom of the device.
There are two additional 6mm Phillips #2 screws under the pads.
Using a Phillips #2 screwdriver, remove the two remaining screws.
Put your hand on the silver bottom case and gently pull it outward.

Remove the four round pads from the bottom of the device.

There are two additional 6mm Phillips #2 screws under the pads.

Using a Phillips #2 screwdriver, remove the two remaining screws.

Put your hand on the silver bottom case and gently pull it outward.

Step 7

Locate the green circuit board. This panel is clipped onto two black, circular-shaped columns at two corners.
Pull out the green circuit board on the two corners.
The green circuit board is attached to a black box at the bottom. Flip the panel and the black box together to open the device.

Locate the green circuit board. This panel is clipped onto two black, circular-shaped columns at two corners.

Pull out the green circuit board on the two corners.

The green circuit board is attached to a black box at the bottom. Flip the panel and the black box together to open the device.

Step 8

Remove the two 2.5 mm Phillips #1 screws securing the lightning dock assembly to the device.
Remove the two screws and the black cover.
Gently remove the lightning dock assembly.
The lightning dock assembly is connected to wires.

Remove the two 2.5 mm Phillips #1 screws securing the lightning dock assembly to the device.

Remove the two screws and the black cover.

Gently remove the lightning dock assembly.

The lightning dock assembly is connected to wires.

Step 9

Remove the two 2.5mm screws using a Phillips #1 screwdriver.
Remove the back cover.
Use your fingers to reposition the lightning connector.
Make sure ALL of the lightning connector is exposed.

Remove the two 2.5mm screws using a Phillips #1 screwdriver.

Remove the back cover.

Use your fingers to reposition the lightning connector.

Make sure ALL of the lightning connector is exposed.

Step 10

              Screen

Look at the side of the device. You will see a green panel connecting to the black box by a white stripe.
Remove the four 2.5 mm Phillips #1 screws on the green panel.
Flip the green panel to reveal the front of the screen.

Look at the side of the device. You will see a green panel connecting to the black box by a white stripe.

Remove the four 2.5 mm Phillips #1 screws on the green panel.

Flip the green panel to reveal the front of the screen.

Step 11

Locate the transparent, rectangular plastic screen cover.
Gently lift the cover off.
The screen is now revealed. Replace the screen with a functioning one.

Locate the transparent, rectangular plastic screen cover.

Gently lift the cover off.

The screen is now revealed. Replace the screen with a functioning one.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 1 other contributor

                    Chen Zhong

Member since: 02/05/2019

569 Reputation

                                      4 Guides authored                  



                       Badges:
                       6







                                                        +3 more badges

Team

                       UC Davis, Team S18-G5, Lore Winter 2019                        

                                                  Member of UC Davis, Team S18-G5, Lore Winter 2019 



                    UCD-LORE-W19S18G5                     


                                            3 Members                     


                                            4 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team