Difficulty
Moderate
Steps
13
Time Required
1 hour
Sections
1
- Compressor Relay
- 13 steps
Flags
0
BackRefrigerator
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Compressor Relay
- Clear out all food products in the refrigerator.
- Unplug the plug from the outlet.
- Turn the refrigerator backward.
- Don’t turn the mini fridge on its side. Doing so will ruin the mini fridge gas.
Clear out all food products in the refrigerator.
Unplug the plug from the outlet.
Turn the refrigerator backward.
Don’t turn the mini fridge on its side. Doing so will ruin the mini fridge gas.
1024
Step 2
- Use a knife to cut the plastic holding strips.
- Don’t damage the rubber covering. Damaging it can be dangerous when turning the mini fridge back on.
Use a knife to cut the plastic holding strips.
Don’t damage the rubber covering. Damaging it can be dangerous when turning the mini fridge back on.
Step 3
- Use your thumbs to open the rubber covering.
Use your thumbs to open the rubber covering.
Step 4
- Use the CR-V screwdriver to unscrew the screw by rotating the screwdriver counter clockwise.
Use the CR-V screwdriver to unscrew the screw by rotating the screwdriver counter clockwise.
Step 5
- Push the flathead screwdriver upward to pry open the metal hinge.
- Repeat this same step on the other side.
Push the flathead screwdriver upward to pry open the metal hinge.
Repeat this same step on the other side.
Step 6
- Remove the plastic box by pulling it away from the wires.
Remove the plastic box by pulling it away from the wires.
Step 7
- Stick the flathead screwdriver in between the compressor relay and the pot.
- Wiggle the screwdriver left to right five times.
- Use your hand to pull the compressor relay from the pot.
Stick the flathead screwdriver in between the compressor relay and the pot.
Wiggle the screwdriver left to right five times.
Use your hand to pull the compressor relay from the pot.
Step 8
- Use the flathead screwdriver to push the white cable against the compressor relay to disconnect it.
Use the flathead screwdriver to push the white cable against the compressor relay to disconnect it.
Step 9
- Connect the white cable to the new compressor relay.
- You should hear a click when you connect it correctly.
Connect the white cable to the new compressor relay.
You should hear a click when you connect it correctly.
Step 10
- Connect the holes on the compressor relay to the pot.
- Connect the top hole on the white part of the compressor relay first, then connect the rest of the holes.
Connect the holes on the compressor relay to the pot.
Connect the top hole on the white part of the compressor relay first, then connect the rest of the holes.
Step 11
- Hold the plastic box as shown in the picture and put it on the compressor relay.
- Reattach the metal hinge back onto the plastic box.
- You should hear a click when putting back on the metal hinge.
- These two steps must be done at the same time in order to work.
Hold the plastic box as shown in the picture and put it on the compressor relay.
Reattach the metal hinge back onto the plastic box.
You should hear a click when putting back on the metal hinge.
These two steps must be done at the same time in order to work.
Step 12
- Reattach the screw to the green wire and use the CR-V screwdriver to reinsert the screw.
- Refer back to Step 4 to help you complete this step.
Reattach the screw to the green wire and use the CR-V screwdriver to reinsert the screw.
Refer back to Step 4 to help you complete this step.
Step 13
- Warp the rubber coating back onto the metal wire.
- Warp the new plastic holding stripes onto the rubber coating.
Warp the rubber coating back onto the metal wire.
Warp the new plastic holding stripes onto the rubber coating.
Cancel: I did not complete this guide.
Author
with 2 other contributors
Rizwan Laghari
Member since: 09/30/2021
217 Reputation
1 Guide authored
Badges:
3
Team
University of North Texas, Team 1-7, Raign Fall 2021
Member of University of North Texas, Team 1-7, Raign Fall 2021
UNT-RAIGN-F21S1G7
2 Members
1 Guide authored
