Featured
Featured Guide
Difficulty
Easy
Steps
11
Time Required
Suggest a time??
Sections
3
- Battery
- 2 steps
- Keyboard
- 7 steps
- RAM
- 2 steps
Flags
1
Featured Guide
This guide has been found to be exceptionally cool by the iFixit staff.
BackiBook G4 14" 933 MHz-1.33 GHz
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Use a coin to rotate the battery locking screw 90 degrees clockwise.
Use a coin to rotate the battery locking screw 90 degrees clockwise.
1024
Step 2
- Lift the battery out of the computer.
Lift the battery out of the computer.
Step 3
Keyboard
- Pull the keyboard release tabs toward you and lift up on the keyboard until it pops free.
- If the keyboard does not come free, use a small flathead screwdriver to turn the keyboard locking screw 180 degrees in either direction and try again. The locking screw is in between the F5 and F6 keys and is a clear piece of plastic.
- Flip the keyboard over, away from the screen, and rest it face-down on the trackpad area.
Pull the keyboard release tabs toward you and lift up on the keyboard until it pops free.
If the keyboard does not come free, use a small flathead screwdriver to turn the keyboard locking screw 180 degrees in either direction and try again. The locking screw is in between the F5 and F6 keys and is a clear piece of plastic.
Flip the keyboard over, away from the screen, and rest it face-down on the trackpad area.
Step 4
- If the computer has an AirPort card installed, follow the next three steps to remove it.
- Push the wire clasp away from the AirPort card and toward the display, then rotate up to free it from the RAM shield.
If the computer has an AirPort card installed, follow the next three steps to remove it.
Push the wire clasp away from the AirPort card and toward the display, then rotate up to free it from the RAM shield.
Step 5
- Grasp the clear plastic tab on the AirPort card and pull toward the display.
Grasp the clear plastic tab on the AirPort card and pull toward the display.
Step 6
- Hold the AirPort card in one hand and use your other hand to remove the antenna cable.
Hold the AirPort card in one hand and use your other hand to remove the antenna cable.
Step 7
- Remove the four silver Phillips screws that secure the RAM shield.
Remove the four silver Phillips screws that secure the RAM shield.
Step 8
- Grasp the metal bracket on top of the RAM shield and pull upward to remove the shield.
Grasp the metal bracket on top of the RAM shield and pull upward to remove the shield.
Step 9
- Pull the keyboard cable up from the logic board, holding the cable as close to the connector as possible.
- Make sure that you reconnect the keyboard cable before replacing the RAM shield.
Pull the keyboard cable up from the logic board, holding the cable as close to the connector as possible.
Make sure that you reconnect the keyboard cable before replacing the RAM shield.
Step 10
RAM
- Release the tabs on each side of the RAM chip at the same time. These tabs lock the chip in place and releasing them will cause the chip to “pop” up.
Release the tabs on each side of the RAM chip at the same time. These tabs lock the chip in place and releasing them will cause the chip to “pop” up.
Step 11
- Pull the chip directly out from its connectors.
Pull the chip directly out from its connectors.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
32 other people completed this guide.
Attached Documents
- iBook-G4-14"-Screw-Guide.pdf
- PDF - 721.28 kb
- View
iBook-G4-14"-Screw-Guide.pdf
PDF - 721.28 kb
Author
with 5 other contributors
iRobot
Member since: 09/24/2009
1 Reputation
646 Guides authored
Badges:
36
+33 more badges
