Featured

Featured Guide

Difficulty

Easy

Steps

9

Time Required

Suggest a time??

Sections

3

  • Battery
  • 1 step
  • Keyboard
  • 7 steps
  • RAM
  • 1 step

Flags

1

This guide has been found to be exceptionally cool by the iFixit staff.

  • BackiBook G3 14"

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Use a coin to rotate the battery locking screw 90 degrees clockwise.
  • Lift the battery out of the computer.

Use a coin to rotate the battery locking screw 90 degrees clockwise.

Lift the battery out of the computer.

1024

Step 2

              Keyboard
  • Pull the keyboard release tabs (highlighted in red) toward you and lift up on the keyboard until it pops free.
  • If the keyboard does not come free, use a small flathead screwdriver to turn the keyboard locking screw 180 degrees in either direction and try again.
  • Flip the keyboard over, away from the screen, and rest it face-down on the trackpad area.

Pull the keyboard release tabs (highlighted in red) toward you and lift up on the keyboard until it pops free.

If the keyboard does not come free, use a small flathead screwdriver to turn the keyboard locking screw 180 degrees in either direction and try again.

Flip the keyboard over, away from the screen, and rest it face-down on the trackpad area.

Step 3

  • If your computer does not have an AirPort card installed, skip to the RAM shield removal step.
  • Push the wire clasp toward the AirPort card and pull it up to free it from the RAM shield.

If your computer does not have an AirPort card installed, skip to the RAM shield removal step.

Push the wire clasp toward the AirPort card and pull it up to free it from the RAM shield.

Step 4

  • Grasp the clear plastic tab on the AirPort card and pull toward the right.

Grasp the clear plastic tab on the AirPort card and pull toward the right.

Step 5

  • Hold the AirPort card in one hand and use your other hand to remove the antenna cable.

Hold the AirPort card in one hand and use your other hand to remove the antenna cable.

Step 6

  • Remove the two Phillips screws that secure the RAM shield.

Remove the two Phillips screws that secure the RAM shield.

Step 7

  • Grasp the metal bracket on top of the RAM shield and pull upward to remove the shield.

Grasp the metal bracket on top of the RAM shield and pull upward to remove the shield.

Step 8

  • Pull the keyboard cable up from the logic board, holding the cable as close to the connector as possible.

Pull the keyboard cable up from the logic board, holding the cable as close to the connector as possible.

Step 9

              RAM
  • Release the tabs on each side of the RAM chip at the same time. These tabs lock the chip in place and releasing them will cause the chip to “pop” up.
  • Pull the chip directly out from its connectors.

Release the tabs on each side of the RAM chip at the same time. These tabs lock the chip in place and releasing them will cause the chip to “pop” up.

Pull the chip directly out from its connectors.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      11 other people completed this guide.

Attached Documents

  • iBook-G3-14"-Screw-Guide.pdf
  • PDF - 671.35 kb
  • View

iBook-G3-14"-Screw-Guide.pdf

PDF - 671.35 kb

Author

                                      with 4 other contributors 


                    iRobot

Member since: 09/24/2009

1 Reputation

                                      646 Guides authored                  



                       Badges:
                       36





                                                        +33 more badges