Difficulty
Moderate
Steps
7
Time Required
15 - 30 minutes
Sections
1
- Screen
- 7 steps
Flags
Needs Better Images
Better photos will improve this guide. Help out by taking, editing, or uploading new ones!
BackIBM ThinkPad T43
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Screen
- Locate the screws holding the screen cover in place.
- There are 3 screws on the left side, 4 on the right, and 4 across the bottom of the screen.
Locate the screws holding the screen cover in place.
There are 3 screws on the left side, 4 on the right, and 4 across the bottom of the screen.
1024
Step 2
- Remove the covers by inserting plastic spudger in between the edge of the cover and laptop.
- Remove screws by using the Phillips head #0
- The covers are set in with an adhesive so they may pop off when removing them.
Remove the covers by inserting plastic spudger in between the edge of the cover and laptop.
Remove screws by using the Phillips head #0
The covers are set in with an adhesive so they may pop off when removing them.
Step 3
- Insert the flat metal spudger into the edge of the screen cover and slowly pry open.
- Slide the spudger along the edges and pry open to release the cover from the clips
- While slide the spudger up the side of the cover, pinch the cover to help unhook the clips
- Across the bottom of the screen there is an adhesive, so you will need to carefully pry of that part of the cover
Insert the flat metal spudger into the edge of the screen cover and slowly pry open.
Slide the spudger along the edges and pry open to release the cover from the clips
While slide the spudger up the side of the cover, pinch the cover to help unhook the clips
Across the bottom of the screen there is an adhesive, so you will need to carefully pry of that part of the cover
Step 4
- Remove the two screws located near the bottom middle of the screen
Remove the two screws located near the bottom middle of the screen
Step 5
- Flip over the green rectangular shaped board
- Disconnect the screen from the rectangular board using your fingers or tweezers
Flip over the green rectangular shaped board
Disconnect the screen from the rectangular board using your fingers or tweezers
Step 6
- Using “Flat metal spudger” lift up the screen from the bottom slowly until you see the ribbon cable
- Detach the ribbon cable before lifting completely the screen
- Now you be able to remove the screen
- Because of how the ribbon cable is connected, it may detach when you lift the screen up
Using “Flat metal spudger” lift up the screen from the bottom slowly until you see the ribbon cable
Detach the ribbon cable before lifting completely the screen
Now you be able to remove the screen
Because of how the ribbon cable is connected, it may detach when you lift the screen up
Step 7
- To replace the screen follow the next set of steps
- Using your fingers or tweezers, pull out the light by placing them on the sides and lifting up
- Insert the wide plug on the ribbon cable into the new screen and place back into the laptop.
- Now if you follow these steps in reverse order, you will be able to finish replacing the screen
To replace the screen follow the next set of steps
Using your fingers or tweezers, pull out the light by placing them on the sides and lifting up
Insert the wide plug on the ribbon cable into the new screen and place back into the laptop.
Now if you follow these steps in reverse order, you will be able to finish replacing the screen
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 2 other contributors
aLiX pIeRRe
Member since: 03/19/2018
816 Reputation
5 Guides authored
Badges:
10
+7 more badges
Team
UMass Dartmouth, Team S6-G4, Bernier Spring 2018
Member of UMass Dartmouth, Team S6-G4, Bernier Spring 2018
UMASSD-BERNIER-S18S6G4
4 Members
10 Guides authored